Sharp PN-ZS1C Leaflet
- 4 -
- 1 -
Printed in Japan
EN(1)
PN-ZS1C
Operation Manual
Stand cover
Applicable models (as of July 2008) LCD MONITOR LB-1085
Thank you for purchasing a SHARP product.
Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the
section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be
accessed at any time.
section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be
accessed at any time.
TIPS
Please understand that Sharp Corporation bears no responsibility for errors made during use by the customer or a third party,
nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized
under law.
This product and its accessories may be upgraded without advance notice.
nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized
under law.
This product and its accessories may be upgraded without advance notice.
To ensure safe and correct use
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels
and incorrectly using the product could have results as classified below.
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all
instructions.
and incorrectly using the product could have results as classified below.
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all
instructions.
Warning:
Not following these instructions could result in death or serious injury.
The installation must be performed by qualified service personnel.
Improper installation work may cause the monitor to fall or topple over, resulting in injury.
Secure the stand with the anchor bolts before assembling these parts.
Secure the stand with the anchor bolts before assembling these parts.
Otherwise, the monitor may topple over, resulting in injury.
Only use the accessories with specified models. Do not modify the LCD Monitor or the accessories.
Only use the accessories with specified models. Do not modify the LCD Monitor or the accessories.
Otherwise, the monitor may fall or topple over, resulting in injury.
Caution:
Not following these instructions could result in injury or property damage.
Tighten all the screws and bolts fully and securely.
Insufficient tightening may cause the monitor to fall or topple over, resulting in injury.
When any deformation or cracks are found please stop using the LCD Monitor.
When any deformation or cracks are found please stop using the LCD Monitor.
Using the monitor without repairing the problem may cause the monitor to fall or topple over, resulting in injury.
•
-
-
•
•
•
•
•
Model
PN-ZS1C
Dimensions See the figure below.
Weight
Approx. 77 kg (169.8 lbs.) (Weight includes
support rods, covers and screws)
support rods, covers and screws)
As a part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
Unit: mm (inch)
(The figure shows the approximate values.)
1670 (65
3
/
4
)
634
(24
15
/
16
)
815*
(32
1
/
16
)
* Height when mounted at 1600 mm (63 inch)
715 mm (28
1
/
8
inch) when mounted at 1500 mm (59
1
/
16
inch)
Main specifications
Installation procedure
(continued)
5
Attach the left and right back cover with 16 supplied
M6 screws.
Back cover
Cables can
be bundled by
attaching the cable
clamp to the back
cover.
6
Attach the cover reinforcement angle with the
supplied M6 screws to secure the front cover. (Use
10 screws for 1600 mm (63 inch), 7 screws for
1500 mm (59
10 screws for 1600 mm (63 inch), 7 screws for
1500 mm (59
1
/
16
inch).)
*
*
*
* Not used when 1500 mm (59
1
/
16
inch)