Sharp LC-24LE210E User Manual
Initial auto installation
When the TV is powered on for the first time after purchase,
the initial auto installation wizard appears. Follow the menus
and make the necessary settings one after another.
the initial auto installation wizard appears. Follow the menus
and make the necessary settings one after another.
1 Press a on the TV.
• The initial auto installation wizard appears.
2 Setting the OSD language.
Press
a/b/c/d
to select the desired language.
3 Setting the country.
Press
▲/▼/◄/► to select your country or area.
4 Select broadcast settings.
Press
▲/▼ to select “Tune type”. Press ◄/► to
select between differents tune type:
CADTV:
Cable digital broadcasts.
ATV:
Analogue broadcasts.
DTV:
Digital broadcasts.
DTV + ATV:
Digital and analogue broadcasts.
CADTV+ATV:
Cable and analogue broadcasts.
5 Starting channel search.
Press
▲/▼ to select “Channel tuning” and then
press OK.
• If you want to search for more broadcasts,
execute “DTV (or ATV, or CADTV) manual
tuning” from the menu “CHANNEL” (Page 20).
tuning” from the menu “CHANNEL” (Page 20).
• To watch both analogue broadcasts and digital
broadcasts, you should perform the channel
search setting “DTV+ATV” or “CADTV+ATV”.
search setting “DTV+ATV” or “CADTV+ATV”.
• Is not possible to search digital and cable digital
broadcasts at the same time.
6 Selecting the TV location.
Quick guide
Press
◄/► to select where you will use this TV, and
then press OK.
•HOME: For home.
•STORE: DYNAMIC mode is predetermined. If the
“Picture Mode” is changed, the TV will automatically
switch back to “DYNAMIC” when there is no signal input
from the TV or remote control unit for 30 minutes.
•STORE: DYNAMIC mode is predetermined. If the
“Picture Mode” is changed, the TV will automatically
switch back to “DYNAMIC” when there is no signal input
from the TV or remote control unit for 30 minutes.
If you have chosen “STORE” by mistake, go to “OPTION”
→ “Restore Factory Default” → OK, and the TV returns
to the initial screen.
→ “Restore Factory Default” → OK, and the TV returns
to the initial screen.
7 The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
and the connected antenna.
•
To cancel the initial auto installation in progress, press
END
.
NOTE
•
If you turn the power on the TV after performing step 4,
initial auto installation wizard does not appear. The auto
installation function allows you to execute the installation
again from the “CHANNEL” menu (Page 20).
initial auto installation wizard does not appear. The auto
installation function allows you to execute the installation
again from the “CHANNEL” menu (Page 20).
•
After initial Auto Tuning is completed, the default PIN is
automatically set to “1234”. To change the PIN setting,
refer to “LOCK” menu on page 22.
automatically set to “1234”. To change the PIN setting,
refer to “LOCK” menu on page 22.
If you install a DVB-T antenna for the first time of relocate
it, you should adjust the alignment of the antenna to
receive a good reception while checking the antenna
setup screen.
1 Press a channel you want to check.
2 Press MENU. “PICTURE” menu will appear.
3 Press ◄/► to select “CHANNEL” menu.
4 Press ▲/▼ to select “Signal Information” and
it, you should adjust the alignment of the antenna to
receive a good reception while checking the antenna
setup screen.
1 Press a channel you want to check.
2 Press MENU. “PICTURE” menu will appear.
3 Press ◄/► to select “CHANNEL” menu.
4 Press ▲/▼ to select “Signal Information” and
then press OK.
5 Position and align the antenna so that the maximum
possible values for “Quality” and “Strength” are
obtained.
obtained.
NOTE
The values of “Quality” and “Strength” indicate when to check
the appropriate alignment of the antenna.
the appropriate alignment of the antenna.
Checking quality and
signal strength
Home
Store
9
Confirm the following before turning
on the power
on the power
E Is the antenna cable connected?
E Is the AC cord plugged in?