Kenwood DDX35 User Manual
72
English
Accessories/Installation Procedure
Accessories
1
..........1
2
..........1
(2m)
3
..........1
4
*
1
..........2
5
*
2
..........2
6
*
2
..........1
7
*
3
..........1
(3m)
*
1
DDX4023BT/
DDX4053BT/
DDX3023/DDX3053/
DDX42BT/DDX35 only.
DDX3023/DDX3053/
DDX42BT/DDX35 only.
*
2
DDX6023BT/
DDX6053BT only.
*
3
DDX6023BT/
DDX6053BT/
DDX4023BT/
DDX4053BT/DDX42BT
only.
DDX4023BT/
DDX4053BT/DDX42BT
only.
Installation Procedure
1 To prevent a short circuit, remove the key
from the ignition and disconnect the
·
battery.
2 Make the proper input and output wire
connections for each unit.
3 Connect the speaker wires of the wiring
harness.
4 Take Connector B on the wiring harness
and connect it to the speaker connector
in your vehicle.
in your vehicle.
5 Take Connector A on the wiring harness
and connect it to the external power
connector on your vehicle.
connector on your vehicle.
6 Connect the wiring harness connector to
the unit.
7 Install the unit in your car.
8 Reconnect
8 Reconnect
the
· battery.
9 Press the reset button.
10 Perform the Initial Setup.
10 Perform the Initial Setup.
WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
supply must be connected to the wires via the
fuse.
¤
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
damage the unit.
• If the power is not turned ON (“Miswiring
DC Offset Error”, “Warning DC Offset Error” is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
• Only for DDX6023BT/DDX6053BT: If the console
has a lid, make sure to install the unit so that the
faceplate will not hit the lid when closing and
opening.
faceplate will not hit the lid when closing and
opening.
EN_GET0909-001A_EQ.indb 72
EN_GET0909-001A_EQ.indb 72
12/11/13 15:27
12/11/13 15:27