Furuno MU-190 User Manual

Page of 41
MU-190
OPERATOR'S MANUAL
www.furuno.com
MODEL
取 扱 説 明 書
MONITOR UNIT
表示部

Summary of Contents of user manual for Furuno MU-190

  • Page 1

    OPERATOR'S MANUAL 取 扱 説 明 書 MONITOR UNIT 表示部 MODEL MU-190 www.furuno.com

  • Page 2

    (Elemental Chlorine Free) The paper used in this manual is elemental chlorine free. ・ 機器の修理・使用方法等に関するお問い合わせは、お買い上げの販売店・代理店、最寄りの   当社支店・営業所あてへお願いします。 ・ FURUNO...

  • Page 3: IMPORTANT NOTICES

    IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international us- ers....

  • Page 4: SAFETY INSTRUCTIONS

    SAFETY INSTRUCTIONS Read these safety instructions before you operate the equipment. Indicates a condition that can cause death or...

  • Page 5

    SAFETY INSTRUCTIONS Safety Instructions for the Installer WARNING CAUTION Turn off the power at the switchboard Observe the following...

  • Page 6: TABLE OF CONTENTS

    TABLE OF CONTENTS Note: This manual contains both English and Japanese instructions. The Installation Materials, Outline Drawings, and Interconnection Diagram...

  • Page 7: FOREWORD

    FOREWORD A Word to the Owner of the MU-190 FURUNO Electric Company thanks you for purchasing the MU-190 19” Monitor...

  • Page 8: SYSTEM CONFIGURATION

    SYSTEM CONFIGURATION RGB FSV-30/30S, etc. DVI (2 ports) FAR-21x7, FEA-2107, FCR-21x7, etc. VIDEO (NTSC/PAL) CCD camera, DVD recorder, etc. RS-232C...

  • Page 9: EQUIPMENT LISTS

    EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Monitor Unit MU-190 - 1 Installation CP26-01600 000-019-210 1 set...

  • Page 10: 1. MOUNTING, WIRING

    1. MOUNTING, WIRING 1.1 Preparation Mounting method You can install the monitor unit as follows. See the outline drawings at...

  • Page 11

    1. MOUNTING, WIRING 1.2 Flush Mount, Fixed at Front Flush mount, fix at front is the standard installation method....

  • Page 12

    1. MOUNTING, WIRING 7. Set the masking panel to each side of the monitor unit. Masking Panel for 19” LCD...

  • Page 13

    1. MOUNTING, WIRING 1. Use the flush mounting template (supplied) to make a cutout in the mounting location. 2....

  • Page 14

    1. MOUNTING, WIRING 7. Set the cutouts of the hood (19) assembly to the knobs on the hood fixing plates...

  • Page 15

    1. MOUNTING, WIRING 3. Screw the wing bolts and the wing nuts of the flush mount fixture 19 so...

  • Page 16

    1. MOUNTING, WIRING 1.5 Flush Mount, Fixed at Rear, with Hood The flush mount, fixed at rear method allows you...

  • Page 17

    1. MOUNTING, WIRING 6. Set the cutouts of the hood (19) assembly to the knobs on the hood fixing...

  • Page 18

    1. MOUNTING, WIRING 2. Set the mounting bracket to the mounting location with four self-tapping screws. Self-Tapping Screw (4 places)...

  • Page 19

    1. MOUNTING, WIRING 1.7 Flush Mount a Series Side by Side You can flush mount two or three monitor...

  • Page 20

    1. MOUNTING, WIRING 1.8 Wiring Refer to the figure below and the interconnection diagram at the back of this manual...

  • Page 21: 2. ADJUSTMENTS

    2. ADJUSTMENTS Adjust the MU-190 according to the equipment connected. Note: Sections 2.2, 2.3 and 2.4 are for Non-SOLAS. 2.1...

  • Page 22

    2. ADJUSTMENTS 1. Press the S or T key to select the menu item to adjust on the [INSTALLATION SETTING]...

  • Page 23

    2. ADJUSTMENTS How to open the [INSTALLATION SETTING] menu Turn off the monitor unit. While you hold the DISP...

  • Page 24

    2. ADJUSTMENTS [RGB], [DVI1/2] menu descriptions Menu item Function Setting H_SIZE (Only for Adjust the image size horizontally. Depending on...

  • Page 25

    2. ADJUSTMENTS 2.3 Video Composite Signal Setting (For Non-SO- LAS) You can adjust the VIDEO signal from the VIDEO...

  • Page 26

    2. ADJUSTMENTS 2.4 The Menu Window Setting (For Non-SOLAS) 2.4.1 How to adjust the menu window You can adjust the...

  • Page 27

    2. ADJUSTMENTS 2.4.2 How to change the signal name You can change the signal name ([RGB], [DVI1/2] or [VIDEO])...

  • Page 28: 3. OPERATION

    3. OPERATION Note: When you connect the monitor unit to FAR-21x7, FEA-2107 or FCR-21x7, you can turn the power on/off...

  • Page 29

    3. OPERATION Slide switch “ON” The external equipment connected to the DVI port (DVI-D1 or DVI-D2) can turn on/off...

  • Page 30

    3. OPERATION 3.4 How to Select the Source for Main Picture Select the signal to display on the entire screen...

  • Page 31

    3. OPERATION 2. Press the X key to select [SYSTEM]. RGB DVI1 DVI2 VIDEO OSD SYSTEM AUTO DIMMER OFF...

  • Page 32: 4. MAINTENANCE,TROUBLESHOOTING

    4. MAINTENANCE, TROUBLESHOOTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the...

  • Page 33

    4. MAINTENANCE, TROUBLESHOOTING Item Life Type Code Number FAN1 Approximately 40,000 hours MFB52A-12HA-001 000-172-023-10 FAN4 Approximately 60,000 hours LQ0DDB0094...

  • Page 34: SPECIFICATIONS

    FURUNO MU-190 SPECIFICATIONS OF MONITOR UNIT MU-190 1 GENERAL 1.1 Display 19-inch color LCD 1.2 Effective area 376.32 x 301.06...

  • Page 35: INSTALLATION MATERIALS

    A-1 CODE NO. 001-116-250-00 26AH-X-9401 -2 TYPE CP26-01601 1/1 工事材料表 MU-190 INSTALLATION MATERIALS 番 号 名  称 略  図 型名/規格 数量...

  • Page 36: OUTLINE DRAWINGS

    20/May/2011 Y.NISHIYAMA D-1

  • Page 37

    3/Mar/2011 Y.NISHIYAMA D-2

  • Page 38

    3/Mar/2011 Y.NISHIYAMA D-3

  • Page 39

    1/Mar/2011 Y.NISHIYAMA D-4

  • Page 40: INTERCONNECTION DIAGRAM

    1 2 3 4 表示部 *2 DVI-D1 DVI-D/D SINGLELINK5M/10M DVI-D レーダー制御部 MONITOR UNIT J3 5/10m,φ7 J3 RADAR PROCESSOR UNIT...

  • Page 41: Declaration of Conformity

downloadlike
ArtboardArtboardArtboard
Report Bug