Land Pride RCD1884 User Manual
27
Section 5: Maintenance & Lubrication
12/15/15
RCD1884 Rotary Cutters 326-355M
Skid Shoe Maintenance (Accessory)
Refer to Figure 5-7:
!
WARNING
If the accessory skid shoes are mounted on the cutter
side skirts, check them for wear and replace as needed.
Order only genuine Land Pride parts from your local Land
Pride dealer.
side skirts, check them for wear and replace as needed.
Order only genuine Land Pride parts from your local Land
Pride dealer.
1.
Remove 3/8" hex whiz nuts (#3), flat washers (#4),
3/8" plow bolts (#2), and skid shoes (#1) as shown.
3/8" plow bolts (#2), and skid shoes (#1) as shown.
2.
Check plow bolts for wear and replaced if necessary.
3.
Attach new skid shoes (#1) to cutter with existing
3/8" plow bolts (#2), flat washers (#4), and 3/8" hex
whiz nuts (#3). Tighten nuts to the correct torque.
3/8" plow bolts (#2), flat washers (#4), and 3/8" hex
whiz nuts (#3). Tighten nuts to the correct torque.
Skid Shoe Accessory
Figure 5-7
Long Term Storage
Clean, inspect, service, and make necessary repairs to
the cutter when parking it for long periods and when
parking it at the end of a working season. This will help
ensure the cutter is ready for field use the next time you
hook-up to it.
the cutter when parking it for long periods and when
parking it at the end of a working season. This will help
ensure the cutter is ready for field use the next time you
hook-up to it.
!
CAUTION
!
DANGER
Weld-on Skid Shoe
Replaceable Skid Shoe
Land Pride Skid Shoe Replacement Parts
Item Part No.
Part Description
1
312-602D
SKID SHOE
2
802-603C
BOLT, PLOW 3/8" - 16 x 1" GR5
3
803-013C
NUT, LOCK 3/8-16 PLT
4
804-012C
WASHER, FLAT 3/8 SAE PLT
33003
!
DANGER
1.
Clean off any dirt and grease that may have
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of deck and then
wash surface thoroughly with a garden hose. A
coating of oil may also be applied to the lower deck
area to minimize oxidation.
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of deck and then
wash surface thoroughly with a garden hose. A
coating of oil may also be applied to the lower deck
area to minimize oxidation.
2.
Check blades and blade mounting hardware for
wear. Replace blades and hardware as needed. See
“Cutter Blade Maintenance” on page 24.
wear. Replace blades and hardware as needed. See
“Cutter Blade Maintenance” on page 24.
3.
Inspect for loose, damaged, or worn parts and adjust
or replace as needed.
or replace as needed.
4.
Repaint parts where paint is worn or scratched to
prevent rust. Ask your dealer for Land Pride aerosol
touch-up paint. They are also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
prevent rust. Ask your dealer for Land Pride aerosol
touch-up paint. They are also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
5.
Replace all damaged or missing decals.
6.
Lubricate unit. See “Lubrication” on page 28.
7.
Store cutter on a level surface in a clean, dry place.
Inside storage will reduce maintenance and make for
a longer cutter life.
Inside storage will reduce maintenance and make for
a longer cutter life.
8.
Follow all unhooking instructions on page 23 when
disconnecting tractor from cutter.
disconnecting tractor from cutter.
Ordering Replacement Parts
Land Pride offers equipment in factory standard beige
with black highlights. Equipment may also be purchased
in Green, Red or Orange. Special attention must be given
to the part number to prevent ordering the wrong color. A
suffix number corresponding to one of the colors below
must be added at the end of the part number. Parts
ordered without the suffix number will be supplied in
factory standard colors.
with black highlights. Equipment may also be purchased
in Green, Red or Orange. Special attention must be given
to the part number to prevent ordering the wrong color. A
suffix number corresponding to one of the colors below
must be added at the end of the part number. Parts
ordered without the suffix number will be supplied in
factory standard colors.
For example, if you are ordering a replacement part with
part number 555-555C and the existing part is red, then
add the suffix 83 to the end of the number to make the
part number read 555-555C83.
part number 555-555C and the existing part is red, then
add the suffix 83 to the end of the number to make the
part number read 555-555C83.
Land Pride Aerosol Touch-up Paint
Part No.
Part Description
821-011C
PAINT LP BEIGE AEROSOL SPRAY CAN
821-002C
PAINT LP BLACK AEROSOL SPRAY CAN
821-054C
PAINT MEDIUM RED AEROSOL SPRAY CAN
821-058C
PAINT GREEN AEROSOL SPRAY CAN
821-066C
PAINT ORANGE AEROSOL SPRAY CAN
81 . . . . . . Green
82 . . . . . . Orange
82 . . . . . . Orange
83 . . . . . . . Red
85 . . . . . . . Black
85 . . . . . . . Black