Fantom Vacuum PT205HA User Manual

Remove the plug 

from the power source before 

assembly of leaf blower. This will 
help prevent accidental starting of 
the unit which could result in serious 
injury.

The impeller rotates for 

a few seconds after you turn off the 

blower and will cause injury. WAIT until all 
parts stop moving.

Instructions must be followed in 

order.
1.

Remove all parts from the packaging.

2.

Remove the nuts and screws 
provided from the packaging.

3.

Insert the blower/vacuum tube all the 
way into the opening on the motor 
housing until the holes in the tabs on 
the blower/vacuum tube align with 
the screw holes in the housing. (Fig. 1)

2. Slide the vacuum bag over the debris 

exhaust tube on the housing. (Fig. 2)

Motor Housing

Blower/Vacuum

Tube

Nut

Self-Tapping

Screw

Screw

Screw

Self-Tapping

Screw

Nut

Air Intake
(Vacuum)

Air Output

(Blower)

Fig. 2

4.

Insert the two (2) screws into the 
right side of the motor housing the 
two (2) nuts into the left side of the 
motor housing. (Fig. 1)

5.

Tighten the screws firmly.  Do NOT
over-tighten.

6.

Insert the two (2) self-tapping screws 
into the holes on either side of the 
blower outlet housing. (Fig. 2 )

7.

Tighten the screws firmly but do 
NOT over-tighten.

: If it is necessary to disassemble 

the leaf blower, follow these instructions:
8.

Turn the unit “Off” and remove the 
plug from the extension cord.

9.

Remove the two (2) self tapping 
screws from either side of the blower 
outlet housing.

10. Remove the two (2) screws and nuts 

holding the blower/vacuum tube to 
the housing.

: Place the all the screws and nuts 

in a safe place for future use.
11. Remove the blower/vacuum tube 

from the motor housing.

: Always replace the 

blower/vacuum tube before using the leaf 
blower.

The leaf blower will not run 

unless the vacuum tube is locked in 
place.

Remove the plug 

from the power source before 

assembly of leaf blower. This will 
help prevent accidental starting of 
the unit which could result in serious 
injury.
1.

Slide the buckle that is on the 
vacuum bag onto the vacuum 
bag hook that is on the 
underside of the blower/vacuum 
tube. (Fig. 3)

Fig. 4

3. Tighten the vacuum bag onto the 

debris exhaust tube and fasten the 
velcro strap securely on top of the 
ridge created for the bag cuff. (Fig. 4)

4. To remove the vacuum bag, loosen 

the velcro strap and pull the vacuum 
bag off of the debris exhaust tube. 
(Fig. 5)

Fig. 5

5. Always replace the vacuum bag 

before using the leaf blower.

Pull vacuum 

bag down

If the shoulder strap is not already put 
together:
1. Push the end through the center of 

the buckle.

2. Pull the strap over the cross bar and 

down through the slot in the buckle. 
(Fig. 6) 

Fig. 6

3. Fully extend the shoulder strap. 

(Fig. 7)

Fig. 7

4. Attach the metal clip of the shoulder 

strap to the latch support on top of the 
handle. (Fig. 8)

Fig. 8

5. Place the shoulder 

strap over your 
head and opposite 
shoulder. (Fig. 9)

6. While in the 

operating position, 
adjust the length 
of the shoulder 
strap to fit your 
height. To lengthen 
the shoulder strap, 
pull the strap down 
and move he buckle 
up. To shorten, pull 
the strap back through the buckle 
while moving the buckle down. 
(Fig. 10)

Fig. 9

Fig. 10

To Lengthen

To Shorten