Shindaiwa 81704 User Manual

12

NEVER operate the unit with the cut-

ting attachment shield or other protective 

devices removed!

 

WARNING!

A cutting attachment shield or other 

protective device is no guarantee of 

protection against ricochet. YOU MUST 

ALWAYS GUARD AGAINST FLYING 

DEBRIS!

Tilt the handle about 

100° to the left (from 

horizontal) and move 

forward, holding the 

trimmer vertically as 

shown in Figure 25.

Your Shindaiwa unit may be equipped with one 

of several Shindaiwa trimmer head models, 

each with features for  specific applications 

and/or operational requirements.

NOTE:

For proper operation, always refer to the 

instructions accompanying the trimmer head 

being used. Available trimmer head styles 

include:

n

 

Semi-automatic. Trimmer line is 

indexed when the operator taps the  

trimmer head on the ground during 

operation.

n

 

Manual. The operator indexes line man-

ually with the grass trimmer stopped.

n

 

Fixed. The operator must stop the unit 

and add new lengths of trimmer line 

manually.

n

 

Flail. This device, designed for clearing 

weeds and light brush, features three 

nylon blades attached to the head by 

pivots.

NOTE:

Additional hardware may be required to 

mount the Fixed Line or the Flail type trim-

mer heads.

Cutting Grass—Units equipped with a trimmer head

CAUTION!
Operation at low RPM can lead to  

premature clutch failure.

Checking Unit Condition

Shoulder Strap C2510

CAUTION!
Operation of trimmer without a cutting at-

tachment shield and using excessive line 

length can lead to premature clutch failure.

Use only authorized Shindaiwa parts and 

accessories with your Shindaiwa trimmer. 

Do not make modifications to this unit with-

out written approval from Shindaiwa, Inc.
ALWAYS make sure the cutting attach-

ment is properly installed and firmly tight-

ened before operation.
NEVER use a cracked or warped cutting  at-

tachment: replace it with a serviceable one.
ALWAYS make sure the cutting attach-

ment fits properly into the appropriate 

attachment holder. If a properly installed 

attachment vibrates, replace the attach-

ment with new one and re-check. 
ALWAYS stop the engine immediately  

and check for damage if you strike a for-

eign object or if the unit becomes tangled. 

Do not operate with broken or damaged 

equipment.
NEVER allow the engine to run at high 

RPM without a load. Doing so could  dam-

age the engine.
NEVER operate a unit with worn or  dam-

aged fasteners or attachment holders.

CAUTION!
Do not push the rotating line into trees, 

wire fences or any material that could 

tangle or break line ends.

Operate the unit at full throttle while cut-

ting grass.

 

WARNING!

 

  Always wear a shoulder strap 

or harness when operating this unit. 

Using a harness with a brushcutter 

allows you to maintain proper control 

of the unit and reduces fatigue during 

extended operation.

IMPORTANT!

Adjust the shoulder strap so the shoulder pad 

rests comfortably on the off-side shoulder and 

the cutting path of  the cutting attachment 

is parallel to the ground. Make sure all 

hooks and adjustment devices are secure.

(optional accessory)

Adjust the double shoulder harness straps 

so the shoulder pads rest comfortably 

on the shoulders and the cutting path of 

the blade is parallel to the ground. Make 

sure all hooks and adjusting devices are 

secure.

B45045

Hold the trimmer so the trimmer head is 

angled slightly into the area to be cut. To 

ensure maximum trimmer-line service life, 

cut only with the tip of the trimmer line. 

Cut grass by swinging the trimmer from 

left to right. Keep the trimmer head  hori-

zontal. See Figure 24.

CUTTING

PATH

RETURN

PATH