Electrolux AG15538A User Manual
23
38
38
42
42
TO REPLACE MOWER BLADE DRIVE
BELT
The mower blade drive belt may be re-
placed without tools. Park the tractor on
level surface. Engage parking brake.
BELT
The mower blade drive belt may be re-
placed without tools. Park the tractor on
level surface. Engage parking brake.
BELT REMOVAL -
1. Place attachment clutch in “DIS EN -
1. Place attachment clutch in “DIS EN -
GAGED” po si tion.
2. Move at tach ment lift lever forward to
lower mower to its lowest position.
3. Roll belt off engine pulley.
4. Disconnect R.H. suspension arm from
4. Disconnect R.H. suspension arm from
rear deck brack et by removing retainer
spring.
spring.
5. Work belt off both mandrel pulleys and
idler pulleys.
6. Pull belt away from mower.
BELT INSTALLATION -
1. Work new belt around both mandrel
BELT INSTALLATION -
1. Work new belt around both mandrel
pulleys and idler pulleys.
2. Install new belt into engine pulley
grove.
3. Reconnect R.H. suspension arm and
secure with retainer spring.
4. Make sure belt is in all pulley grooves
and inside all belt guides.
Mandrel
Pulley
Pulley
Retainer
Spring
Spring
R.H. Suspension Arm
Mandrel
Pulley
Pulley
Idler
Pulleys
Pulleys
Engine
Pulley
Pulley
With parking brake “Engaged”
1-1/2"
Jam Nut
Operating Arm
Nut “A”
TO CHECK AND ADJUST BRAKE
Your tractor is equipped with an ad just able
brake system which is mounted on the
right side of the transaxle.
If tractor requires more than fi ve (5) feet to
stop at highest speed in high est gear on a
level, dry concrete or paved surface, then
brake must be checked and ad just ed.
Your tractor is equipped with an ad just able
brake system which is mounted on the
right side of the transaxle.
If tractor requires more than fi ve (5) feet to
stop at highest speed in high est gear on a
level, dry concrete or paved surface, then
brake must be checked and ad just ed.
TO CHECK BRAKE
1. Park tractor on a level, dry concrete or
1. Park tractor on a level, dry concrete or
paved surface, depress clutch/brake
pedal all the way down and engage
parking brake.
pedal all the way down and engage
parking brake.
2. Place gear shift lever in neutral (N)
position.
The rear wheels must lock and skid when
you try to manually push the tractor for-
ward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to
be replaced.
you try to manually push the tractor for-
ward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to
be replaced.
TO ADJUST BRAKE
1. Depress clutch/brake pedal all the way
1. Depress clutch/brake pedal all the way
down and en gage parking brake.
2. Measure distance between brake op er -
at ing arm and nut “A” on brake rod.
3. If distance is other than 1-1/2", loos en
jam nut and turn nut “A” until dis tance
becomes 1-1/2". Re tight en jam nut
against nut “A”.
becomes 1-1/2". Re tight en jam nut
against nut “A”.
4. Road test tractor for proper stopping
distance as stated above. Readjust
if nec es sary. If stopping distance is
still greater than fi ve (5) feet in high est
gear, further main te nance is nec-
es sary. Contact an authorized service
center/department.
if nec es sary. If stopping distance is
still greater than fi ve (5) feet in high est
gear, further main te nance is nec-
es sary. Contact an authorized service
center/department.