Toro 3250-D User Manual

53

2015 Toro Commercial Equipment Guide 15-003-T    Rev. 2/15

GREENSMASTER 3250-D, MODEL 04384

ENGINE

Kubota® 902 tier 4i, 3-cylinder liquid-cooled diesel engine. 55.0 cu. in. (902 cc). Full pressure lubrication, oil filter. 24.8 hp (18.5 kW) @ 3600 rpm. Engine governed 

to 2760 rpm high idle, 1500 rpm low idle (no load).

FUEL CAPACITY

6 gallons (22.7 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).

TRACTION DRIVE

Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.

GROUND SPEED

Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum 

Greensmaster 3250-D transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph 

(4.0 km/h) maximum.

TURF COMPACTION

10 psi (.68 bar) average at recommended minimum tire pressures, with a 200 lb. operator, and cutting units down.

STEERING

Power steering. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has through shaft design for 

accurate straight line steering.

CONTROLS/GAUGES

Raise/lower-mow lever. Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter  

and 4 bulb warning cluster. Hand operated choke, throttle. Mechanical engine speed control.

ELECTRICAL FEATURES 

Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C) 40 amp 

alternator, circuit fused at 40 amps. Ignition switch/key. Seat switch. High temperature engine kill override switch. Harness terminals, fuse slot, and console switch 

location available for optional lights installation.

SOUND LEVEL

84 dBA at operator ear under normal conditions.

OVERALL DIMENSIONS

 

Width of Cut: 

59.0" (150 cm) 

Overall Height: 

77.5" (197 cm) 

 

Wheel Tread: 

50.5" (128 cm) 

Net Weight (no fuel, no operator):  1,216 lbs. (552 kg) 

 

Wheel Base: 

48.6" (123 cm) 

Reel Speed: 

Approx.1950 rpm @ 2760 rpm (Adjustable) 

 

Overall Length (w/baskets): 

93.9" (238 cm) 

 

 

Overall Width: 

68.0" (173 cm)

TIRES

Three 19 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable. Smooth tread (approx. 1290 rev/mile). 8-12 psi front; 8-15 psi rear.

LEAK DETECTION

Turf Guardian™ optional.

BACKLAPPING

Standard equipment.

BRAKES

6" (15.2 cm) drum type mechanical with rack and pawl lock for parking.

SEAT

Contour seat with high backrest. 7" (17.8 cm) fore/aft slider adjustment with two mounting positions, allowing 9" (22.8 cm) total seat travel. Operator manual tube 

mounted on the seat back for easy access.

ROPS

Roll over protection system standard.

CERTIFICATION

Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.

WARRANTY

Two-year limited warranty. Refer to the Operator’s Manual for further details. 

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.  

Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

8 BLADE DPA CUTTING UNITS, 04618

11-BLADE DPA CUTTING UNITS, 04619   14-BLADE CUTTING UNITS, 04624

TRACTOR

These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex 33xx/34xx series).

HEIGHT OF CUT (HOC) RANGE

Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, 

range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

REEL WELDMENT

Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness. The 

reel is ground for diameter and concentricity, and backgrind.

REEL BEARINGS

Two double row, self-aligning ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft with lock nut. Multiple seal barriers on both sides of bearing for 

added protection. Reel position maintained by a wave washer with no adjusting nut. 

MAINTENANCE

No grease zerks, sealed bearing design eliminates daily maintenance.

REEL DRIVE

The reel weldment shaft is a 1.375" (35 mm) diameter tube with drive inserts permanently pressed in both ends. A replaceable floating coupler with an internal eight 

tooth spline is factory installed on the right end, and held in place by a snap ring. The floating coupler may be moved to the other end when the cutting unit is used 

on the GR3250-D front right position.

FRAME

Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.

AGGRESSIVENESS

Aggressiveness stays constant throughout the life of the reel. Patented design.

BEDKNIFE

Replaceable single edged EdgeMax

TM

 Microcut Bedknife is standard. 

BEDKNIFE ADJUSTMENT

Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm)  bedknife movement for each position. 

FRONT & REAR ROLLERS

Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller.   

Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.

GRASS SHIELD

Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.

TOTAL WEIGHT

8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller.   11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller.   14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.

The Greensmaster 3250-D is manufactured  
in Tomah, WI  ISO 9002 Certified Plant.