Black & Decker BDPE200B User Manual

4) Service

•  Do not use this paint edger for purposes other than described in this manual. Failure to do so 

may result in injury to persons and or property damage.  

• Keep hands out of the plunger drive area of the paint edger. Fingers can be pinched 

between the plunger drive and the plunger.

• use only with water soluble based paints. Not for use with oil based paints and stains (refer to label 

on original paint container). Do not use with paint removers, solvents, or the like. Liquids other than paint 

may damage product and result in injury to persons or property damage.

• always read and follow the label on the original paint container and follow all 

directions. Failure to do so may result in injury to persons or property damage.

• always use proper eye protection and other safety equipment for skin and respiratory 

protection when mixing the paint, and when filling, using, and cleaning the product. Paint and its 

fumes can cause personal injury.

• to reduce the risk of injury, always work in a properly ventilated area and wear 

appropriate respiratory protection if necessary. Fumes from some paints can be noxious.

• thoroughly clean and rinse product after using with a particular paint. Mixing different paints in 

the product may cause personal injury and or result in property damage.

• to reduce the risk of injury, use only recommended accessories.

• When servicing, use only identical replacement parts. Failure to do so may result in personal injury.
  The label on your tool may include the following symbols.

 ........................ earthing terminal

(figure a)
1. Main Body

2. On/Off Trigger

3. Flow Control Knob

4. Battery Cap

5. Battery Cap Release Tabs

6. Paint Applicator*

7. Paint Applicator Release Tabs

8. Paint Tube*

9. Plunger*

10. Plunger Drive

11. Fill Sleeve

12. Fill Sleeve Locking Tabs

13. Fill Sleeve Paint Can Clips

 batteries can explode, or leak, and can cause injury or fire. 

To reduce this risk:

• Carefully follow all instructions and warnings on the battery label and package. 

• Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and 

the equipment. 

• Do not short battery terminals. 

• Do not charge batteries. 

• Do not mix old and new batteries. Replace all of them at the same time with new batteries of 

the same brand and type. 

• Remove dead batteries immediately and dispose of per local codes. 

• Do not dispose of batteries in fire. 

• Keep batteries out of reach of children. 

• Remove batteries if the device will not be used for several months.

“Transporting batteries can possibly cause fires if the battery terminals inadvertently come 

in contact with conductive materials such as keys, coins, hand tools and the like. The US 

Department of Transportation Hazardous Material Regulations (HMR) actually prohibit 

transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon 

luggage) UNLESS they are properly protected from short circuits. So when transporting 

individual batteries, make sure that the battery terminals are 

protected and well insulated from materials that could contact 

them and cause a short circuit”.
• Remove the battery cap (4) by pressing in the battery release 

tabs (5) and then sliding the battery cap (4) off the handle.

• Insert 3 fresh 1.5 volt AA batteries into the handle as 

shown in figure b.

• Refit the battery cap (4) by sliding it back on to the handle 

until it is firmly seated.

note: Always place batteries correctly according to the 

polarity (+ and -) as marked on the battery and the tool.
inStalling tHe paint applicator (C)

• Press in the paint applicator release tabs (7).

• Slide the paint applicator into the front of the main body (1) 

of the paint edger until it is firmly seated.

• Release the tabs.

note: The paint applicator can not be fitted with the paint 

tube in place.
removing tHe paint applicator

• Press in the paint applicator release tabs (7).

• Slide the paint applicator out of the main body (1) of the paint edger.

• Release the tabs (7).

note: The paint applicator can not be removed with the paint tube in place.

inStalling tHe paint tube (D, E)

note: The paint tube can not be attached until the paint applicator has been installed.

• Pull the plunger drive (10) to the back of the main body of 

the paint edger and clip it in place as shown in figure D.

• Slide the paint tube (8) forward into the main body of the 

paint edger as shown in figure e.

ntoe: Ensure the paint tube is fully seated in the main body 

by firmly pressing it forward.

• Pull the plunger drive back and up to release it, then gently 

guide the plunger drive’s tip into the recess on the top of 

the plunger.

note: The plunger drive will not push the plunger until it 

has been unclipped from the locked position.
removing tHe paint tube 

• Pull the plunger drive to the back of the main body of the 

paint edger and clip it in place.

• Pull paint tube backwards and lift the paint tube out of the 

main body of the paint edger.

 

read all safety warnings and all instructions. Failure 

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable 

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause you 

a) Stay alert, watch what you are doing and use common sense when operating a 

drugs, alcohol or medication. A moment of inattention while operating power tools 

b) use personal protective equipment. always wear eye protection. Protective equipment such 

will reduce personal injuries.

c) prevent unintentional starting. ensure the switch is in the off position before connecting to 

d) remove any adjusting key or wrench before turning the power tool on. A wrench or a key left 

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of 

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves 

away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

g) if devices are provided for the connection of dust extraction and collection facilities, ensure 

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

3) poWer tool uSe anD care

a) Do not force the power tool. use the correct power tool for your application. The correct 

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot 

be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool 

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with 

e) maintain power tools. check for misalignment or binding of moving parts, breakage of parts 

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges 

g) use the power tool, accessories and tool bits, etc. in accordance with these instructions, 

taking into account the working conditions and the work to be performed. Use of the power 

Safety guiDelineS - DefinitionS 

It is important for you to read and understand this manual. The information it contains 

relates to protecting your Safety and preventing problemS. The symbols below 

are used to help you recognize this information. 

 Indicates an imminently hazardous situation which, if not avoided, 

will result in death or serious injury.

 Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

 Indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

 Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.