Ariens 926014 ST9526DLE User Manual
GB - 15
Discharge Chute Control
IMPORTANT: If chute does not stay in set position,
adjust as directed in SERVICE AND ADJUSTMENTS
on page 22, or repair before operation.
adjust as directed in SERVICE AND ADJUSTMENTS
on page 22, or repair before operation.
Rotate the Chute with Discharge Chute Control.
IMPORTANT: DO NOT force frozen chute controls. If
frozen, take to warm place until controls are free.
frozen, take to warm place until controls are free.
Heated Handles (926002, 003, 014, 015, 016,
500, 501)
500, 501)
Turn the heated handles switch to the
ON (1) position to activate. Turn the
switch to the OFF (2) position to
deactivate.
ON (1) position to activate. Turn the
switch to the OFF (2) position to
deactivate.
Remote Differential (926013, 014, 015, 016,
500, 501)
500, 501)
Squeeze and hold the remote differential lever to lock
differential so both wheels drive and provide better
traction. Release the remote differential lever to allow
easier steering.
differential so both wheels drive and provide better
traction. Release the remote differential lever to allow
easier steering.
If remote differential does not engage or disengage
properly, adjust or repair before operation (see
REMOTE DIFFERENTIAL (926013, 014, 015, 016,
500, 501) on page 23).
properly, adjust or repair before operation (see
REMOTE DIFFERENTIAL (926013, 014, 015, 016,
500, 501) on page 23).
Remote Wheel Lock (926002, 003)
Squeeze and release the remote wheel lock to lock the
left wheel for better traction when throwing snow or to
unlock the left wheel for easier steering.
left wheel for better traction when throwing snow or to
unlock the left wheel for easier steering.
NOTE: The wheel lock will not release when under
load. Do not unlock the wheel while turning. If the
wheel lock will not release, turn the unit slightly left or
right to relieve axle load and release the axle lock.
load. Do not unlock the wheel while turning. If the
wheel lock will not release, turn the unit slightly left or
right to relieve axle load and release the axle lock.
If remote wheel lock does not lock or unlock properly,
adjust or repair before operation (see REMOTE
WHEEL LOCK (926002, 003) on page 23).
adjust or repair before operation (see REMOTE
WHEEL LOCK (926002, 003) on page 23).
Axle Lock Pin (926001)
Use the axle lock pin to lock or unlock the right or left
wheel. Lock both wheels to increase traction; unlock
one wheel to allow for easier turning of the unit.
wheel. Lock both wheels to increase traction; unlock
one wheel to allow for easier turning of the unit.
NOTE: Unit will not drive with both wheels unlocked.
Scraper Blade
The scraper blade allows the back of the housing to
keep better contact with the surface being cleared. It
also prevents damage to the housing from normal
wear.
keep better contact with the surface being cleared. It
also prevents damage to the housing from normal
wear.
IMPORTANT: DO NOT allow Scraper Blade to wear
too far or Auger/Impeller housing will become
damaged.
too far or Auger/Impeller housing will become
damaged.
Runners
The runners control the distance between the scraper
blade and the ground. Adjust runners equally to keep
blade level with the ground. Refer to Pre-Start on
page 16 for recommended settings.
blade and the ground. Adjust runners equally to keep
blade level with the ground. Refer to Pre-Start on
page 16 for recommended settings.
Drift Cutters (Figure 15)
Drift cutters break up snow drifts that are taller than the
auger housing and direct the snow into the auger. Store
the drift cutters on the auger housing when not in use.
Install them as shown below so they are taller than the
snow to be cleared.
auger housing and direct the snow into the auger. Store
the drift cutters on the auger housing when not in use.
Install them as shown below so they are taller than the
snow to be cleared.
Figure 13
OS7105
OS1950
1
2
Figure 14
Wheel Unlocked
Wheel Locked
Axle Lock Pin