American Audio Q-2411 User Manual

Page of 20
©
American Audio
®
   -   www.americanaudio.us   -   Q-2411™ Instruction Manual Page 11
21.  GND (GROUND TERMINAL) - Be sure to connect turntable ground leads to either or both of 
the two available ground terminals. This will reduce the humming and popping noises associated 
with magnetic phono cartridges.
22.  MICROPHONE 2 CONNECTOR - This jack is used to a connect a microphone to the mixer. 
Connect you microphone via this 1/4 inch (6.3mm) jack. The volume output level for this microphone 
will be controlled by its own respective CHANNEL KNOB (19).
23.  CHANNEL  LINE LEVEL SELECTOR SWITCHES - 
These switches are used to change the volt-
age line levels of there respected  Phono / Aux RCA inputs jacks. When connecting turntables with 
magnetic cartridges to these jacks be sure the corresponding switch is in the “PHONO” position, 
and when using line level input devices be sure this switch is in the “AUX” position. Always be sure 
main power is shut off before change the position of the Line Level Selector Switch.
24.  CHANNEL 1: PHONO 1/AUX 1 INPUT - The type of input must directly reflect the selected 
mode of the
 LINE LEVEL SELECTOR SWITCH (23). Turntables equipped with MM pickup cartridge 
(All DJ turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE 
LEVEL SELECTOR SWITCH (23)
 is in the “PHONO 1” position. CD players, Tape Decks and other 
line level instruments may only be connected to these jacks as long as the LINE LEVEL SELEC-
TOR SWITCH (23) 
is in the “AUX 1” position. Never connect line level instruments (CD players, tape 
decks, etc.) to these jacks when the LINE LEVEL SELECTOR SWITCH (23) is in the “PHONO 1” posi-
tion, THIS MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right 
channel input and the white represents the left channel input. Input volume will be controlled by the 
channel one faderThe channel SOURCE SELECTOR SWITCH (4) must be in the "Phono 1/Aux 1" 
position, to monitor any source connected to these jacks.
      CHANNEL 1: LINE 1 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS! 
CD players, Tape Decks and other line level instruments may be connected to these jacks. The red 
colored RCA jack represents the right channel input and the white represents the left channel input. 
Input volume will be controlled by channel one faderThe channel SOURCE SELECTOR SWITCH (4) 
must be in the "Line 1" position, to monitor any source connected to these jacks.
25.  CHANNEL 2: PHONO 2/AUX 2 INPUT - The type of input must directly reflect the selected 
mode of the LINE LEVEL SELECTOR SWITCH (23). Turntables equipped with MM pickup cartridge 
(All DJ turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE 
LEVEL SELECTOR SWITCH (23)
 is in the “PHONO 2” position. CD players, Tape Decks and other 
line level instruments may only be connected to these jacks as long as the LINE LEVEL SELEC-
TOR SWITCH (23) 
is in the “AUX 2” position. Never connect line level instruments (CD players, tape 
decks, etc.) to these jacks when the LINE LEVEL SELECTOR SWITCH (23) is in the “PHONO 2” posi-
tion, THIS MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right 
 Q-2411™
                                     REAR PANEL - CONTROLS AND FUNCTIONS
LINE 5
1
2
SERIAL NO:
CH-4
21
22
29 28 27
26 23
24
23
25
23
32
31
30
33