Zoom G7.1ut User Manual

This effect simulates a tape echo. 
The above two effect types have the same parameters. 

1 – 

2000

mS

0 – 100

0 – 10

0 – 100

Sets the delay time. 

Adjusts the amount of feedback. 
Higher setting values result in a 
higher number of delay sound 

Adjusts the treble attenuation 
of the delay sound. Lower 
setting values result in softer 

Adjusts the level of the effect 
sound mixed to the original 

This is a delay module that allows use of the hold function. 

This is a long delay with a maximum setting of 5000 ms. 

This module comprises wah and filter effects as well as special effects such as ring 
modulator and octave.

This effect varies wah in accordance with picking intensity. 

This effect varies the resonance filter frequency in accordance with picking intensity. 
The above two effect types have the same parameters. 

Befr, Aftr

-10 – -1, 

1 – 10

0 – 10

2 – 100

When this effect type is selected, the four parameters listed 
here can be adjusted with parameter knobs 1 - 4. The setting 
range for each parameter is also shown. Some effect 
parameters are adjusted with the knobs of the pre-amp section.

The note symbol (      ) in the table indicates that the parameter can be synchronized to the 

patch specific tempo. If you select the note symbol as value for the parameter when making the 

setting at the G7.1ut, the parameter value will be synchronized to the patch specific tempo in 

note units (→ p. 35). 

The pedal symbol (         ) in the table indicates that the parameter can be controlled with the 

built-in expression pedal. If you select the parameter as control target when making the setting 

at the G7.1ut (→ p. 30), the expression pedal will adjust the parameter in real time when the 
patch is selected. Parameters with the pedal symbol can also be selected as control targets for 

the ARRM function. 

The tap (          ), hold (             ), and mute (              ) symbols in the table indicate that the 

respective foot switch can be used to specify the delay time (TAP), toggle hold delay on and off 

(HOLD), or toggle mute between on and off (MUTE). This applies only to the DELAY module. 

To use these functions, the respective function must be assigned to the foot switch (→ p. 34) 
and the respective effect type must be enabled. 

Attenuates high-level signal components and boosts low-level signal components, to keep 
the overall signal level within a certain range. 

This is an MXR Dynacomp type compressor. 

0 – 10

Fast, Slow Tone

0 – 10

2 – 100

Adjusts the compressor 
sensitivity. Higher setting 
values result in higher 
sensitivity. 

Selects compressor attack 
speed in two levels: Fast or 
Slow. 

Adjusts the tonal quality of the 
sound. 

Adjusts the signal level after 
passing the module. 

This effect type allows more detailed adjustment than "Compressor". 

0 – 50

1 – 10

1 – 10

2 – 100

Adjusts the reference signal 
level for the compressor 
action. 

Adjusts the compression ratio. 

Adjusts the compressor attack 
speed. 

Adjusts the signal level after 
passing the module

This is a limiter that suppresses signal peaks above a certain reference level. 

0 – 50

1 – 10

1 – 10

2 – 100

Adjusts the reference signal 
level for the limiter action. 

Adjusts the compression ratio 
of the limiter. 

Adjusts the delay between the 
point where the signal level 
falls below the threshold level 
and the limiter release. 

Adjusts the signal level after 
passing the module. 

This module comprises wah and filter effects as well as special effects such as ring 
modulator and octave.

This effect varies wah in accordance with picking intensity. 

This effect varies the resonance filter frequency in accordance with picking intensity. 
The above two effect types have the same parameters. 

Befr, Aftr

-10 – -1, 

1 – 10

0 – 10

2 – 100

Selects the connection 
position of the WAH/EFX1 
module. Available settings are 
"Befr" (before pre-amp 
section) or "Aftr" (after pre-
amp section). 

Adjusts the effect sensitivity. 

Adjusts the intensity of the 
resonance sound. 

Adjusts the signal level after 
passing the module. 

This is a booster for increasing signal gain. 

1 – 5

0 – 10

0 – 10

2 – 100

Adjusts the frequency range to 
boost

Adjusts the tonal quality of the 
sound. 

Adjusts the amount of boost. 

Adjusts the signal level after 
passing the module.