Roland ARX-01 User Manual
31
In the Effects/Reverb screen you can set the parameters of the
reverb.
reverb.
Setting of Reverb
(Effects/Reverb screen)
(Effects/Reverb screen)
Parameter
Value
Description
Type
0 (OFF),
1 (REVERB),
2 (SRV ROOM),
3 (SRV HALL),
4 (SRV PLATE)
1 (REVERB),
2 (SRV ROOM),
3 (SRV HALL),
4 (SRV PLATE)
Type of reverb
Type: 1 (REVERB)
Type
ROOM1,
ROOM2,
STAGE1,
STAGE2,
HALL1, HALL2,
DELAY,
PAN-DELAY
ROOM2,
STAGE1,
STAGE2,
HALL1, HALL2,
DELAY,
PAN-DELAY
Type of reverb/delay
ROOM1
: short reverb with high density
ROOM2
: short reverb with low density
STAGE1
: reverb with greater late rever-
beration
STAGE2
: reverb with strong early reflec-
tions
HALL1
: very clear-sounding reverb
HALL2
: rich reverb
DELAY
: conventional delay effect
PAN-DELAY
: delay effect with echoes that
pan left and right
Time
0–127
Time length of reverberation(Type:
ROOM1.HALL2)
Delay time(Type: DELAY, PAN-DELAY)
ROOM1.HALL2)
Delay time(Type: DELAY, PAN-DELAY)
HF Damp
200–8000 Hz,
BYPASS
BYPASS
Adjusts the frequency above which the
highfrequency content of the reverb sound
will be cut, or “damped.” If you do not
want to cut the high frequencies, set this pa-
rameter to BYPASS.
highfrequency content of the reverb sound
will be cut, or “damped.” If you do not
want to cut the high frequencies, set this pa-
rameter to BYPASS.
Delay Feed-
back
back
0–127
Adjusts the amount of delay feedback
when the Type setting is DELAY or PAN-DE-
LAY.
when the Type setting is DELAY or PAN-DE-
LAY.
Type:2(SRV ROOM)/3(SRV HALL)/4(SRV PLATE)
Pre Delay
0.0–100.0 ms
Adjusts the delay time from the direct
sound until the reverb sound is heard.
sound until the reverb sound is heard.
Time
0–127
Time length of reverberation
Size
1–8
Size of the simulated room or hall
High Cut
160 Hz–
12.5 kHz,
BYPASS
12.5 kHz,
BYPASS
Adjusts the frequency above which the high-
frequency content of the reverb will be re-
duced. If you do not want to reduce the high
frequencies, set this parameter to BYPASS.
frequency content of the reverb will be re-
duced. If you do not want to reduce the high
frequencies, set this parameter to BYPASS.
Density
0–127
Density of reverb
Diffusion
0–127
Adjusts the change in the density of the re-
verb over time.
verb over time.
The higher the value, the more the density
increases with time. (The effect of this set-
ting is most pronounced with long reverb
times.)
increases with time. (The effect of this set-
ting is most pronounced with long reverb
times.)
LF Damp Freq
50–4000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will
be reduced, or “damped.”
frequency content of the reverb sound will
be reduced, or “damped.”
LF Damp
Gain
Gain
-36–0 dB
Adjusts the amount of damping applied to
the frequency range selected with LF
Damp. With a setting of “0,” there will be
no reduction of the reverb’s low-frequency
content.
the frequency range selected with LF
Damp. With a setting of “0,” there will be
no reduction of the reverb’s low-frequency
content.
HF Damp
Freq
Freq
4000 Hz–
12.5 kHz
12.5 kHz
Adjusts the frequency above which the
highfrequency content of the reverb sound
will be reduced, or “damped.”
highfrequency content of the reverb sound
will be reduced, or “damped.”
HF Damp
Gain
Gain
-36–0 dB
Adjusts the amount of damping applied to
the frequency range selected with HF
Damp. With a setting of “0,” there will be
no reduction of the reverb’s high-frequency
content.
the frequency range selected with HF
Damp. With a setting of “0,” there will be
no reduction of the reverb’s high-frequency
content.
Parameter
Value
Description
ARX-01_e.book 31 ページ ２００８年２月１９日 火曜日 午後４時７分