Yamaha 007POTO-G0 User Manual
78
Sending signals from MIX channels and STEREO/MONO channels to MATRIX buses
LS9-16/32 Owner’s Manual
If the send-destination MATRIX bus is set to stereo,
the screen will change as follows.
the screen will change as follows.
E
TO MATRIX PAN/TO MATRIX BALANCE
knob
knob
This knob adjusts the panning (or the balance, if the
send-source is a STEREO channel or a MIX channel
set to stereo) of the signal sent from this channel to the
two MATRIX buses.
send-source is a STEREO channel or a MIX channel
set to stereo) of the signal sent from this channel to the
two MATRIX buses.
5
To adjust the send level from each channel
to the selected MATRIX bus, move the cur-
sor to a TO MATRIX LEVEL knob in the
screen, and operate the dial or the [DEC]/
[INC] keys.
to the selected MATRIX bus, move the cur-
sor to a TO MATRIX LEVEL knob in the
screen, and operate the dial or the [DEC]/
[INC] keys.
If the send-destination MATRIX bus is set to stereo,
move the cursor to the TO MATRIX PAN (TO
MATRIX BAL) knob and adjust the pan (or balance,
for a STEREO channel or MIX channels set to stereo)
of the signal sent from each channel to the two
MATRIX buses.
move the cursor to the TO MATRIX PAN (TO
MATRIX BAL) knob and adjust the pan (or balance,
for a STEREO channel or MIX channels set to stereo)
of the signal sent from each channel to the two
MATRIX buses.
6
To switch the send position of a signal sent
to the MATRIX bus, move the cursor to the
PRE button in the screen and press the
[ENTER] key.
to the MATRIX bus, move the cursor to the
PRE button in the screen and press the
[ENTER] key.
If the PRE button is on, the pre-EQ or pre-fader signal
will be sent; if this button is off, the signal from imme-
diately after the [ON] key will be sent.
will be sent; if this button is off, the signal from imme-
diately after the [ON] key will be sent.
7
To switch the on/off status of a signal sent
to the MATRIX bus, move the cursor to the
TO MATRIX ON/OFF button in the screen
and press the [ENTER] key.
to the MATRIX bus, move the cursor to the
TO MATRIX ON/OFF button in the screen
and press the [ENTER] key.
If the send-destination MATRIX bus is set to stereo,
operation of the adjacent left/right pair of buttons is
linked.
operation of the adjacent left/right pair of buttons is
linked.
8
If you want to operate a channel that is not
currently shown in the popup window, use
the [SEL] key to select that channel, and
then make settings for it.
currently shown in the popup window, use
the [SEL] key to select that channel, and
then make settings for it.
9
If you want to adjust the send level to
another MATRIX bus, use the keys of the
MIX/MATRIX SELECT section to select
another MATRIX bus, and make settings in
the same way.
another MATRIX bus, use the keys of the
MIX/MATRIX SELECT section to select
another MATRIX bus, and make settings in
the same way.
10
When you’ve finished making settings,
move the cursor to the CLOSE button (or
the
move the cursor to the CLOSE button (or
the
× symbol in the upper right of the win-
dow) and press the [ENTER] key.
Here’s how to use the top panel faders and [ON] keys to
adjust the send level and turn the signal on/off for the sig-
nals sent from the MIX, STEREO (L/R), and MONO
channels to a specific MATRIX bus.
adjust the send level and turn the signal on/off for the sig-
nals sent from the MIX, STEREO (L/R), and MONO
channels to a specific MATRIX bus.
1
Press the SELECTED CHANNEL section
[HOME] key.
[HOME] key.
The SELECTED CH VIEW screen will appear in the
display.
display.
1
SEND popup button
2
Use the LAYER section keys and the chan-
nel module section [SEL] keys to select a
MIX, STEREO (L/R), or MONO channel.
nel module section [SEL] keys to select a
MIX, STEREO (L/R), or MONO channel.
5
• If you’ve turned on POPUP APPEARS WHEN PRESSING
KNOBS in the PREFERENCE popup window (
can also access the above popup window by pressing the
SELECTED CHANNEL section [SELECTED SEND] encoder.
SELECTED CHANNEL section [SELECTED SEND] encoder.
• If PRE is selected as the send position to the MATRIX bus,
then you will also be able to select either PRE EQ (immedi-
ately before the attenuator) or PRE FADER (immediately
before the fader) for each two adjacent odd-numbered/even-
numbered MATRIX buses (
ately before the attenuator) or PRE FADER (immediately
before the fader) for each two adjacent odd-numbered/even-
numbered MATRIX buses (
• If desired, the pan/balance setting of the signal sent to a ste-
reo MATRIX bus can be linked with the TO ST PAN/TO ST
BAL knob of the SELECTED CH VIEW screen (
BAL knob of the SELECTED CH VIEW screen (
HINT
• If the PRE button is on, then you will be able to select either
PRE EQ (immediately before the attenuator) or PRE FADER
(immediately before the fader) for each two adjacent odd-
numbered/even-numbered MATRIX buses (
(immediately before the fader) for each two adjacent odd-
numbered/even-numbered MATRIX buses (
HINT
Using the faders (SENDS ON FADER
mode)
mode)
1