Behringer DDM4000 User Manual

DIGITAL PRO MIXER DDM4000 User Manual

Press the BANK ASSIGN push button to select the memory bank that is 

1) 

to be processed with the effect.
Select the length of the brake by continuously pressing the SELECT 

2) 

push button  

(64)

. This is shown on the display.

Press the SMP FX ON push button  

3) 

(63)

  to activate the effect. 

The push button flashes.

When the sampler comes to an end (SMP FX ON push button and PLAY/OUT push 

button of the selected bank flash), the sampler-effect needs to be deactivated 

by pressing SMP FX ON again in order to restart playback.

Press the SMP FX ON push button to restart playback.

4) 

Press the LOAD push button  

1) 

(35)

. The display switches to “User Setup”. 

The LOAD push button lights up.
Select the factory preset by turning and pressing the left 

2) 

PARAMETER knob  

(45)

.

Press the left PARAMETER knob to confirm the selection.

3) 

Press the LOAD push button  

4) 

(35)

  or the ESC push button  

(52)

  

to exit User Setup.

Press the CONSOLE SETUP knob  

1) 

(51)  

for approximately 2 seconds.

Select “Output Setup” by turning and pressing the CONSOLE SETUP knob. 

2) 

Output Setup appears on the display:

In Output Setup, you make the following settings:

Mono:
Use this function to switch the OUT B outputs  

(74)

  to mono.

Turn the left PARAMETER knob  

1) 

(45)

  to select OFF or ON.

Press the left PARAMETER knob to confirm.

2) 

MODE:
You can use Output A  

(73)

  together with the Subwoofer output, in which case 

the bass frequencies are separated from the Main output (crossover function).

FULL-FREQ: 

MAIN OUT A  

(73) 

 emits the entire frequency 

spectrum (including the bass signal). 

The Subwoofer output gives out the 

subwoofer signal.

CROSSOVER: 

The Subwoofer output gives out the subwoofer 

signal. MAIN OUT A emits frequencies that are 

above the crossover frequency.

Turn the CONSOLE SETUP knob  

1) 

(51) 

 to select the mode 

(FULL-FREQ, CROSSOVER).
Press the CONSOLE SETUP knob to confirm.

2) 

SUB OUT:
The following are used to adjust the crossover frequency and output level 

of the subwoofer output.

FREQ: 

Crossover frequency between SUB OUT and MAIN OUT

GAIN: 

Output level of SUB OUT

TAPE / S/PDIF:
The levels of both Tape and S/PDIF outputs can be adjusted individually.

Press the right PARAMETER knob to select the parameter 

1) 

(FREQ, GAIN or TAPE/ S/PDIF GAIN).
Turn the PARAMETER knob to change the value.

2) 

Press the ESC push button to exit Output Setup.

3) 

Press the LOAD push button  

1) 

(35)

. User Setup appears on the display.

Turn the right PARAMETER knob  

2) 

(45) 

 to change the con-trast.

Press the LOAD push button to exit User Setup.

3) 

The DDM4000 can be used to control DJ or sequencer software applications 

by converting individual mixer sections on the mixer to MIDI controllers 

and assigning these to defined software functions. The MIDI interface 

(76)

  is used to transmit the data. To connect to the mixer, the computer 

requires a MIDI interface, which can be purchased as USB alternative for a 

very reasonable price.

USB-MIDI Interface*

MIDI IN/OUT/THRU

Laptop

* not included

Fig. 7.1: Connecting the DDM4000 to a computer