Briggs & Stratton R5055H 5.5 HP User Manual

Page of 28
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS 
CRT Models
Page 8
800-345-6007
OPERATION
PRE-START INSPECTION
1.  Make sure all safety guards are in place and all nuts and bolts  
are secure.
2.  check oil level in engine crankcase. See your engine manual for 
procedure and specifications.
3.  Inspect air cleaner for cleanliness. See your engine manual for 
procedure.
4.  check the fuel supply. Fill the fuel tank no closer than 1 inch  
from top of tank to provide space for expansion. See your engine 
manual for fuel recommendations.
5.  Be sure spark plug wire is attached and spark plug is  
tightened securely.
6.  check position of wheels and wheel lockouts.
7.  check depth regulator lever position.
8.  Examine  underneath  and  around  engine  for  signs  of  oil  or  fuel 
leaks.
9.  Inspect fuel hoses for tightness and fuel seepage.
10. Look for signs of engine damage.
11. Remove excessive debris from muffler area and recoil starter.
START-UP
The controls required to start and run the rototiller are located on the 
engine and are marked “choke” and “Throttle”.
A  more  detailed  description  of  engine  operation  and  all  related 
precautions and procedures can be found in the engine manufacturer’s 
manual that accompanies each tiller.
COld STARTS
1.  Move choke lever to full choke position.
2.  Move throttle lever to “start”.
3.  Pull  starting  rope  out  slowly  one  time  and  allow  to  return 
normally.
4.  Pull starting rope out rapidly, and allow rope to return normally.
5.  When  engine  starts,  gradually  move  choke  lever  to “no  choke” 
position and increase throttle speed.
RESTARTING A WARm ENGINE
Restarting an engine that is already warm from previous running does 
not normally require use of the choke.
1.  Move throttle lever to “start” position.
2.  Pull starting rope out rapidly until engine starts. Allow rope to return 
normally. Repeat until engine starts.
3.  Adjust throttle speed to “high” for best tiller action.
PlEASE  dO  NOT  START YOUR TIllER  UNTIl 
YOU  hAvE  REAd ThE  mANUAl ThAT  CAmE 
WITh YOUR ENGINE, ANd ThE SECTIONS IN ThIS 
mANUAl TITlEd CONTROlS, AdjUSTmENTS ANd 
SAFETY. IF YOU hAvE REAd ThESE, FOllOW ThE 
STEPS BElOW TO START YOUR TIllER. AlWAYS 
PERFORm ThIS PRE-START ChECklIST BEFORE 
STARTING ThE ENGINE.
GASOlINE  IS  hIGhlY  FlAmmABlE  ANd  mUST 
BE hANdlEd WITh CARE. NEvER FIll ThE TANk 
WhEN ThE ENGINE IS hOT OR RUNNING. AlWAYS 
mOvE OUTdOORS TO FIll ThE TANk.
WhEElS  mUST  AlWAYS  BE  lOCkEd  IN ThE 
TIllING  POSITION WhEN  ENGINE  IS  RUNNING. 
dO NOT OPERATE ThE TIllER WITh ThE WhEEl 
lOCkOUTS  UNlOCkEd.  AlWAYS  SET  ThE 
WhEElS IN TIllING POSITION BEFORE STARTING 
ENGINE.
AlWAYS PUT ThE dEPTh REGUlATOR lEvER IN 
ThE TRANSPORT  POSITION  BEFORE  STARTING 
ENGINE. TINES ShOUld ClEAR ThE GROUNd.
ImPORTANT
ENGINE IS ShIPPEd FROm FACTORY WIThOUT OIl. 
YOU mUST Add ENGINE OIl BEFORE STARTING 
ENGINE.
AlWAYS  kEEP  hANdS  ANd  FEET  ClEAR  OF 
ROTATING mAChINE PARTS.
CAUTION
!
WARNING
!
dANGER
!