Jet Tools JDP-17FSE User Manual
16
Troubleshooting
Trouble Probable
Cause Remedy
Drill press will not start.
1. Drill
press
unplugged from
wall, or motor.
2. Fuse blown, or circuit
breaker tripped.
3. Cord
damaged.
4. Starting capacitor bad.
1. Check all plug connections.
2. Replace fuse, or reset circuit
2. Replace fuse, or reset circuit
breaker.
3. Replace
cord.
4. Replace starting capacitor.
Drill press does not come up
to speed.
to speed.
1. Extension cord too light or
too long.
2. Low
current.
1. Replace with adequate size
and length cord.
2. Contact a qualified
electrician.
Drill Press vibrates
excessively.
excessively.
1. Stand on uneven surface.
2. Bad
2. Bad
belt(s).
1. Adjust stand so that it rests
evenly on the floor.
2. Replace
belts.
Noisy Operation.
1. Incorrect belt tension.
2. Dry
2. Dry
spindle.
3. Loose spindle pulley.
4. Loose motor pulley.
4. Loose motor pulley.
1. Adjust belt tension. See
“Changing Spindle Speeds”,
page 12.
page 12.
2. Lubricate spindle. See
“Lubrication” page 15.
3. Check tightness of retaining
nut on pulley, and tighten if
necessary.
necessary.
4. Tighten set screws in pulleys.
Workpiece Burns.
1. Incorrect
Speed.
2. Chips not clearing from hole
or bit.
3. Dull drill bit.
4. Feeding too slow.
4. Feeding too slow.
1. Change to appropriate
speed, see speed and pulley
chart, page 13.
chart, page 13.
2. Retract drill bit frequently to
remove chips.
3. Resharpen, or replace drill
bit.
4. Increase feed rate.
Drill bit wanders.
1. Bit sharpened incorrectly.
2. Bent drill bit.
3. Bit, or chuck not installed
2. Bent drill bit.
3. Bit, or chuck not installed
properly.
1. Resharpen bit correctly.
2. Replace drill bit.
3. Reinstall the chuck, or bit
2. Replace drill bit.
3. Reinstall the chuck, or bit
properly.
Wood splinters on the
underside.
underside.
1. No backing board used.
1. Place a scrap board
underneath the workpiece to
prevent splintering.
prevent splintering.
Drill bit binds in workpiece.
1. Workpiece pinching the bit.
2. Excessive feed rate.
3. Chuck jaws not tight.
4. Improper belt tension.
2. Excessive feed rate.
3. Chuck jaws not tight.
4. Improper belt tension.
1. Support or clamp workpiece.
2. Decrease feed rate.
3. Tighten chuck jaws.
4. Increase belt tension, see
2. Decrease feed rate.
3. Tighten chuck jaws.
4. Increase belt tension, see
page 12.
Excessive drill bit runout, or
wobble.
wobble.
1. Bent drill bit.
2. Worn spindle bearings.
3. Bit, or chuck not properly
2. Worn spindle bearings.
3. Bit, or chuck not properly
installed.
1. Replace drill bit.
2. Replace spindle bearings.
3. Reinstall the bit, or chuck
2. Replace spindle bearings.
3. Reinstall the bit, or chuck
properly.
Quill returns too slow, or too
fast.
fast.
1. Spring has improper tension.
1. Adjust “Return Spring
Tension,” page 14.
Chuck, or arbor do not stay in
place.
place.
1. Dirt, grease, etc on arbor,
chuck, or spindle.
1. Clean all mating surfaces
thoroughly with a cleaner
degreaser.
degreaser.