Olivetti 2301 User Manual
22
NORMAL COPYING
COPYING FROM THE DOCUMENT GLASS
1
Open the document cover/RSPF and
place the original face down on the
document glass.
place the original face down on the
document glass.
[How to place the original]
Align the corner or the original with the tip of the arrow
(
Align the corner or the original with the tip of the arrow
(
) at the left rear corner of the glass as shown in the
illustration.
2
Close the document cover/RSPF.
The original size appears
in the touch panel.
in the touch panel.
3
Make sure that the same size of paper
as the original is automatically
selected.
as the original is automatically
selected.
The selected tray is
highlighted. If the tray
contains a different size of
paper than the original,
"LOAD xxxx PAPER." will
appear.
highlighted. If the tray
contains a different size of
paper than the original,
"LOAD xxxx PAPER." will
appear.
Even if the message above is displayed, copying can
be performed using the selected paper tray.
be performed using the selected paper tray.
Manually selecting the paper size (paper tray)
If auto paper selection is disabled in the key operator
programs, or if you wish to use a different size of paper than
the original, touch the [PAPER SELECT] key and select the
paper tray with the desired paper size. (The selected paper
will be highlighted and the paper selecting screen will close.)
To close the screen without selecting a paper size, touch the
[PAPER SELECT] key again.
programs, or if you wish to use a different size of paper than
the original, touch the [PAPER SELECT] key and select the
paper tray with the desired paper size. (The selected paper
will be highlighted and the paper selecting screen will close.)
To close the screen without selecting a paper size, touch the
[PAPER SELECT] key again.
4
Select the number of copies and any
other desired copy settings, and then
press the [START] key (
other desired copy settings, and then
press the [START] key (
).
• The number in the copy quantity display will decrease
by 1 each time a copy is made.
• If you are only making a single copy, the copy can be
made with the copy number display showing "0".
• To clear a mistake, press the [CLEAR] key (
).
If "AUDITING MODE" (p.56) has been enabled, enter your 5-digit account number.
Note
If the original size is not automatically
detected, manually set the original size. (p.47)
detected, manually set the original size. (p.47)
R
Original scale
Original scale
A4
A3
B5
B4
A4
R
B5
Note
AUTO
EXPOSURE
AUTO A4
PAPER SELE
100%
COPY RATI
A4
ORIGINAL
A4
A4
A3
• To load paper, see "LOADING PAPER"
(p.15). If you change the paper size in the
tray, you will also need to change the tray's
paper size and paper type settings. (p.19)
tray, you will also need to change the tray's
paper size and paper type settings. (p.19)
• The paper types for the auto paper selection
function can be selected, or the function
disabled, in the key operator programs. (See
the "Key operator's guide".)
disabled, in the key operator programs. (See
the "Key operator's guide".)
• Press the [CLEAR] key (
) to stop
copying in the middle of a run.
• To repeat the same copy sequence for a
different original, simply replace the original
and press the [START] key (
and press the [START] key (
).
• If copying stops because the tray has run
out of paper, you can resume copying by
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray that
has the same size and type of paper loaded
in the same orientation.
touching the [PAPER SELECT] key and
selecting the bypass tray or a paper tray that
has the same size and type of paper loaded
in the same orientation.
Note
READY TO COPY.
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
A3
0
PLAIN
EXTRA IMAGE
ADJUST
RECYCLED
PLAIN
1.A4
2.A3
Note