AMX MVP-7500 Leaflet
Quick Start Guide
MVP-7500
Modero Wireless Touch Panel (Firmware version G4)
For more detailed installation, configuration, programming, file transfer, and
operating instructions refer to the MVP-7500 and MVP-8400 Modero
ViewPoint Touch Panels Instruction Manual, available on-line at
www.amx.com.
operating instructions refer to the MVP-7500 and MVP-8400 Modero
ViewPoint Touch Panels Instruction Manual, available on-line at
www.amx.com.
ATTENTION!
Verify the NetLinx Master Firmware is build 117 or greater for the ME260 and
NI-Series Controllers. Verify the TPDesign4 program being used is Version 2.2
or higher. Earlier versions of the Master firmware and TPD4 software are
incompatible with these panels.
NI-Series Controllers. Verify the TPDesign4 program being used is Version 2.2
or higher. Earlier versions of the Master firmware and TPD4 software are
incompatible with these panels.
Overview
The AMX MVP-7500 panel (FG5965-01) uses an internal wireless compact flash
card to communicate with a NetLinx Master via an off-the-shelf 802.11b Wireless
Access Point. MVP units utilize a 7.5" Color Passive LCD to display a 640 x 480
pixel image using over 4000 colors and features programmable firmware that
can be upgraded via either the wireless card or the mini-USB port. The
MVP-7500 panel also features nine programmable external pushbuttons and two
sets of display LEDs. These panels are configured to operate on a standard
802.11b wireless network. On the 4 available IR channels, this panel utilizes both
AMX IR frequencies (38 KHz or 455 KHz) and 2 additional user-defined IR
libraries.
card to communicate with a NetLinx Master via an off-the-shelf 802.11b Wireless
Access Point. MVP units utilize a 7.5" Color Passive LCD to display a 640 x 480
pixel image using over 4000 colors and features programmable firmware that
can be upgraded via either the wireless card or the mini-USB port. The
MVP-7500 panel also features nine programmable external pushbuttons and two
sets of display LEDs. These panels are configured to operate on a standard
802.11b wireless network. On the 4 available IR channels, this panel utilizes both
AMX IR frequencies (38 KHz or 455 KHz) and 2 additional user-defined IR
libraries.
Specifications
Connections and Wiring
The PS4.4 Power Supply (with barrel connector) provides power to the
MVP-7500 panel either directly (via the power connector located on the lower
right-side of the panel) or indirectly (by routing incoming power through the
Docking Station’s MVP Interface Connector).
MVP-7500 panel either directly (via the power connector located on the lower
right-side of the panel) or indirectly (by routing incoming power through the
Docking Station’s MVP Interface Connector).
•
Once the MVP is connected to a docking station; charging priority is
first given to any MVP-BP battery packs found within the MVP-7500
and then to any other batteries inserted into the docking station’s
battery charging compartments.
and then to any other batteries inserted into the docking station’s
battery charging compartments.
USB Connection
This panel uses a standard version 1.1 Type A to Mini-B 5-Wire USB cable to
provide communication between the touch panel and the PC. This
communication is used to transfer IR data, firmware KIT files, and TPD4 touch
panel files.
provide communication between the touch panel and the PC. This
communication is used to transfer IR data, firmware KIT files, and TPD4 touch
panel files.
WARNING: Although firmware upgrades can be done over wireless Ethernet; it
is strongly recommended that firmware KIT files be transferred over a direct USB
connection and only when the panel is connected to a power supply. If battery
power or wireless connection fails during a firmware upgrade, the panel flash file
system may become corrupted.
is strongly recommended that firmware KIT files be transferred over a direct USB
connection and only when the panel is connected to a power supply. If battery
power or wireless connection fails during a firmware upgrade, the panel flash file
system may become corrupted.
FIG. 1
MVP-7500 Wireless Touch Panel (FG5965-01)
FIG. 2
MVP-7500 Touch Panel component locations
MVP-7500 Panels Specifications
Dimensions (HWD):
• 7.09" x 10.47" x 1.47" (18.00 cm x 26.60 cm x 3.73 cm)
Power: • Full draw: 1.0 A @ 12 VDC
• Full On and charging up to two MVP-BP batteries: 3.0 A @ 12 VDC
Battery Duration:
(
(
per battery)
•
4 hours Normal use (25% On state, 25% Standby, and 50% Sleep).
•
2 hours Continuous use (continuous On state).
Memory:
• 64 MB SDRAM
• 64 MB Compact Flash (upgradable to 1 GB) - factory programmed
• 64 MB Compact Flash (upgradable to 1 GB) - factory programmed
Weight:
• Stand-alone panel: 1.85 lbs (0.84 kg)
• Panel with one battery: 2.25 lbs (1.02 kg)
• Panel with two batteries: 2.65 lbs (1.20 kg)
• Panel with one battery: 2.25 lbs (1.02 kg)
• Panel with two batteries: 2.65 lbs (1.20 kg)
Screen Resolution:
• 640 x 480 pixels (HV) @ 60 Hz frame frequency
Viewing Angle:
• Horizontal: + 55° (left and right) from center
• Vertical: + 25° (up from center) and -35° (down from center)
• Vertical: + 25° (up from center) and -35° (down from center)
Docking station
Mini-USB connector
PWR connector
interface connector
User programmable
pushbuttons (9)
User programmable
status LED
status LED
User
programmable
Stylus LED
Stylus
(side panel)
(front panel)
(fits within
slot on side
panel)
MVP-7500 Panels Specifications (Cont.)
Panel LCD
Parameters:
Parameters:
• Panel type: TFT Color Passive-Matrix
• Aspect ratio: 4 x 3
• Brightness: 120 cd/m
• Aspect ratio: 4 x 3
• Brightness: 120 cd/m
2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 20:1
• Display colors: 4096 colors (12-bit color depth)
• Dot/pixel pitch: 0.23 mm
• Screen Resolution: 640 x 480 pixels (HV) @ 60 Hz frame frequency
• Contrast ratio: 20:1
• Display colors: 4096 colors (12-bit color depth)
• Dot/pixel pitch: 0.23 mm
• Screen Resolution: 640 x 480 pixels (HV) @ 60 Hz frame frequency
External
Components:
Components:
• Docking Station Interface Connector: Metallic strip connector located
on the bottom of the MVP provides communication and power between
the MVP and the optional docking station.
the MVP and the optional docking station.
• LEDs: Two sets of NetLinx programmable LEDs (support On, Off,
and Blink).
• Mini-USB Connector: 5-pin mini-USB connector used for programming
and touch panel file transfer to and from the PC.
• Stylus slot: Illuminated slot where the included stylus can be stored,
located on the left side of the MVP.
• Power Connector: 6mm barrel-style power jack - accepts the power
cord from the PS4.4 power supply (included).
Internal
Components:
Components:
• Wireless Interface card: Provides 802.11b (Type I) wireless connectivity
between the panel and a Wireless Access Point (WAP).
• IR Emitters: Transmit IR over 20 feet (6.10 m) from the panel.
• Internal Buzzer: Emits a Piezo electric tone.
• Battery Compartment: Houses up to two MVP-BP battery packs (one
• Internal Buzzer: Emits a Piezo electric tone.
• Battery Compartment: Houses up to two MVP-BP battery packs (one
MVP-BP is included with the panel).
External Buttons:
• Nine external programmable pushbuttons (four located on the left of the
LCD and five located on the right)
• All of these buttons are user-programmable to activate other
commands (context-sensitive for each page).
Power Modes:
• ON: Panel is fully functional.
• STANDBY: Panel uses low power, the LCD/backlight is shutdown,
• STANDBY: Panel uses low power, the LCD/backlight is shutdown,
LEDs still function. Panel resumes the ON mode in ~ 1 second.
• OFF: On-board programs not running, touch screen still powered, LED
not functional. Panel resumes the ON mode in ~ 30 seconds.
Operating/Storage
Environments:
Environments:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included
Accessories
Accessories
• MVP-7500 Modero Wireless Touch Panel (Firmware version G4)
Quick Start Guide (93-5965-01)
• MVP-BP battery (FG5965-20)
• PS4.4 Power Supply (13.5 VDC) (FG423-44)
• Stylus
• PS4.4 Power Supply (13.5 VDC) (FG423-44)
• Stylus
Optional
Accessories:
Accessories:
• CB-MVPWDS Conduit Box (FG037-10)
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• MVP-BP battery (FG5965-20) (additional/spare)
• MVP-KS Kickstand (FG5965-12)
• MVP-STYLUS three pack (FG5965-30)
• MVP-TDS Table Top Docking Station (FG5965-10)
• MVP-WDS Wall/Flush Mount Docking Station (FG5965-11)
• Upgrade Compact Flash (factory programmed with firmware):
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• MVP-BP battery (FG5965-20) (additional/spare)
• MVP-KS Kickstand (FG5965-12)
• MVP-STYLUS three pack (FG5965-30)
• MVP-TDS Table Top Docking Station (FG5965-10)
• MVP-WDS Wall/Flush Mount Docking Station (FG5965-11)
• Upgrade Compact Flash (factory programmed with firmware):
NXA-CFSP128M - 128 MB compact flash card (FG2116-36)
NXA-CFSP256M - 256 MB compact flash card (FG2116-37)
NXA-CFSP512M - 512 MB compact flash card (FG2116-38)
NXA-CFSP1GB - 1 GB compact flash card (FG2116-39)
NXA-CFSP256M - 256 MB compact flash card (FG2116-37)
NXA-CFSP512M - 512 MB compact flash card (FG2116-38)
NXA-CFSP1GB - 1 GB compact flash card (FG2116-39)