Sharp PNE802 User Manual

You can return the settings to their factory-preset values and

restrict operations.

1. Hold

SIZE

down until “F” appears in the upper left

corner of the screen.

2. While “F” appears, press

in that

order.

▲

OFF

UNLOCKED

ON1

LED

OFF

MONITOR

FUNCTION

1/1

ALL RESET

ADJUSTMENT LOCK

ADJUSTMENT LOCK TARGET

RS-232C

OSD DISPLAY

LED

TEMPERATURE ALERT

STATUS ALERT
POWER BUTTON

CONTROLLER INPUT

END…[MENU]

3. Select and set the items.

ALL RESET
Resets the settings to the factory default settings.
Press

, select ALL RESET, and then press

After initialization, turn the main power switch off and

then back on.
When the PN-ZB01 (optional) is attached, press

select the resetting method, and then press

ALL RESET1 ....Resets all the settings to the factory

default settings.

ALL RESET2 ....Returns all settings to the factory default

settings except for the following items:

LAN SETUP, RS-232C/LAN SELECT,

ID No. SET, BAUD RATE, NETWORK,

MAIL, SERVICE & SUPPORT, and

SNMP (See page 22, and pages 45 to

48.)

ADJUSTMENT LOCK
You can disable operations on the monitor and the

remote control unit that use buttons.

OFF ...Enables operation.

ON 1 ..Disables all operations other than turning power

on/off and FUNCTION.

ON 2 ..Only the FUNCTION operation is enabled.

Disables all operations other than FUNCTION (not

even power on/off).

ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with

ADJUSTMENT LOCK.

REMOTE CONTROL ..... Prohibits remote control

operation

MONITOR BUTTONS ... Prohibits monitor switch

operation

BOTH ............................. Prohibits remote control and

monitor switch operation

RS-232C

(RS-232C/LAN when the PN-ZB01 (optional) is

attached)
Specifies whether to allow control via RS-232C or LAN

(see pages 29 and 41).

Initialization (Reset)/Functional Restriction Setting (FUNCTION)

OSD DISPLAY
Shows/hides the menu, modes and messages.

The FUNCTION screen cannot be hidden.

ON 1 .............. Shows all menus, modes and messages.

ON 2 .............. Hides messages automatically displayed

by the display. Shows messages during

operation.

OFF ............... Hides all menus, modes and messages.
LED
Specifies whether to light the power LED.

OFF cannot be selected when STANDBY MODE is LOW

POWER.
TEMPERATURE ALERT
Selects the notification method for an abnormal

temperature.

OFF .............. Do not notify about an abnormal

temperature.

OSD & LED .. When an abnormal temperature is

detected, the power LED flashes in red

and green alternately and the screen

displays a message: TEMPERATURE.

LED............... When an abnormal temperature is

detected, the power LED flashes in red

and green alternately.

STATUS ALERT
Selects the notification method for a hardware error.

OFF .............. Do not notify about the error.

OSD & LED .. When a hardware error is detected, the

power LED flashes in red and the screen

displays a message: STATUS [xxxx].

LED............... When a hardware error is detected, the

power LED flashes in red.

POWER BUTTON
Normally, leave this setting as MONITOR.

When using an optional part, if instruction appears,

change the setting accordingly.
CONTROLLER INPUT
Normally, you do not need to change this setting.

When using an optional part, if instruction appears,

change the setting accordingly.

4. Press

to return to the normal screen.

TIPS

• When both abnormal temperature and hardware error are

detected, the hardware error notification overrides.

• If TEMPERATURE ALERT or STATUS ALERT is set to

OSD&LED, alert messages will appear even if the OSD

DISPLAY is set to ON 2 or OFF.

• If TEMPERATURE ALERT or STATUS ALERT is set to LED

or OSD & LED, the LED lights even if the LED function is

set to OFF.