Sony CPD-20SF2T5 Manual
9
EN
5
4
3
2
1
8
7
6
15
14
13
12
11
10
9
Pin No.
1
2
3
4
5
6
7
Signal
Red
Green
(Composite
Sync on Green)
(Composite
Sync on Green)
Blue
—
DDC Ground*
Red Ground
Green Ground
Pin No.
8
9
10
11
12
13
14
15
Signal
Blue Ground
DDC + 5V*
Ground
—
Bi-Directional
Data (SDA)*
Data (SDA)*
H. Sync
V. Sync
Data Clock (SCL)*
*
Display Data Channel (DDC) Standard by VESA.
Design and specifications are subject to change without
notice.
notice.
Plug and Play
This monitor complies with the DDC
1, DDC2B and
DDC2AB which are the Display Data Channel (DDC)
standards of VESA.
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
standards and outputs the EDID (Extended Display
Identification) to the data line.
When a DDC2B or DDC2AB host system is connected, the
monitor automatically switches to each communication.
standards of VESA.
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
standards and outputs the EDID (Extended Display
Identification) to the data line.
When a DDC2B or DDC2AB host system is connected, the
monitor automatically switches to each communication.
DDC
is a trademark of Video Electronics Standard Association.
Use of the Tilt-Swivel
With the tilt-swivel, this unit can be adjusted to be viewed at
your desired angle within 90˚ horizontally and 20˚ vertically.
To turn the unit vertically and horizontally, hold it at its
bottom with both hands.
your desired angle within 90˚ horizontally and 20˚ vertically.
To turn the unit vertically and horizontally, hold it at its
bottom with both hands.
15°
45°
45°
5°
Damper Wire
Using a white background, very thin horizontal stripes on
the screen are visible as shown on the illustration. These
stripes are damper wires. These wires are attached to the
aperture grille inside the Trinitron tube and are there to
damp vibrations of the aperture grille in order to prevent
them from influencing to the picture quality.
the screen are visible as shown on the illustration. These
stripes are damper wires. These wires are attached to the
aperture grille inside the Trinitron tube and are there to
damp vibrations of the aperture grille in order to prevent
them from influencing to the picture quality.
Damper wire
Approx. 8 cm
Approx. 8 cm
Specifications
Picture tube
0.30 mm aperture grille pitch
20␣ inches measured diagonally
90-degree deflection
20␣ inches measured diagonally
90-degree deflection
Viewable image size Approx. 388
×
292 mm (w/h)
(15
3
/
8
×
11
1
/
2
inches)
19.1” viewing image
Resolution
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Vertical: Max. 1024 lines
Standard image area Approx. 373
×
280 mm (w/h)
(14
3
/
4
×
11
1
/
8
inches)
or
Approx. 350
Approx. 350
×
280 mm (w/h)
(13
7
/
8
×
11
1
/
8
inches)
Deflection frequency Horizontal: 30 to 85 kHz
Vertical: 48 to 150 Hz
AC input voltage/current
100 to 120 V, 50/60 Hz, 1.7 A
220 to 240 V, 50 – 60 Hz, 1.2 A
220 to 240 V, 50 – 60 Hz, 1.2 A
Power consumption Max. 150 W
Dimensions
Dimensions
Approx. 472
×
493.5
×
501 mm (w/h/d)
(18
5
/
8
×
19
1
/
2
×
19
3
/
4
inches)
Mass
Approx. 29.5 kg (65 lb 1 oz)
Pin assignment
Video signal cable (HD15) (Male)
The cable accepts RGB video signals (0.714 Vp-p, positive),
and SYNC signals.
The cable accepts RGB video signals (0.714 Vp-p, positive),
and SYNC signals.