Sony CPD-E100P User Manual
16
Self-diagnosis function
This monitor is equipped with a self-diagnosis function. If there is
a problem with your monitor or computer, the screen will go
blank and the 1 (power) indicator will either light up green or
flash orange. If the 1 (power) indicator is lit in orange, the
computer is in power saving mode. Try pressing any key on the
keyboard or moving the mouse.
a problem with your monitor or computer, the screen will go
blank and the 1 (power) indicator will either light up green or
flash orange. If the 1 (power) indicator is lit in orange, the
computer is in power saving mode. Try pressing any key on the
keyboard or moving the mouse.
If the 1 (power) indicator is green
1
Disconnect the video input cable or turn off the
connected computer.
connected computer.
2
Press the 1 (power) button twice to turn the monitor
off and then on.
off and then on.
3
Move the control button
, for 2 seconds before the
monitor enters power saving mode.
If all four color bars appear (white, red, green, blue), the monitor
is working properly. Reconnect the video input cable and check
the condition of your computer.
is working properly. Reconnect the video input cable and check
the condition of your computer.
If the color bars do not appear, there is a potential monitor failure.
Inform your authorized Sony dealer of the monitor’s condition.
Inform your authorized Sony dealer of the monitor’s condition.
If the 1 (power) indicator is flashing orange
Press the 1 (power) button twice to turn the monitor off
and then on.
If the 1 (power) indicator lights up green, the monitor is working
properly.
and then on.
If the 1 (power) indicator lights up green, the monitor is working
properly.
If the 1 (power) indicator is still flashing, there is a potential
monitor failure. Count the number of seconds between orange
flashes of the 1 (power) indicator and inform your authorized
Sony dealer of the monitor’s condition. Be sure to note the model
name and serial number of your monitor. Also note the make and
model of your computer and graphic board.
monitor failure. Count the number of seconds between orange
flashes of the 1 (power) indicator and inform your authorized
Sony dealer of the monitor’s condition. Be sure to note the model
name and serial number of your monitor. Also note the make and
model of your computer and graphic board.
Specifications
CRT
0.24 mm aperture grille pitch (center)
15 inches measured diagonally
90-degree deflection
15 inches measured diagonally
90-degree deflection
Viewable image size
Approx. 285
× 214 mm (w/h)
(11
1
/
4
× 8
1
/
2
inches)
14.0" viewing image
Resolution
Maximum
Horizontal: 1280 dots
Vertical: 1024 lines
Vertical: 1024 lines
Recommended
Horizontal: 800 dots
Vertical: 600 lines
Vertical: 600 lines
Standard image area
Approx. 270
× 202 mm (w/h)
(10
3
/
4
× 8 inches)
Deflection frequency*
Horizontal: 30 to 70 kHz
Vertical: 48 to 120 Hz
Vertical: 48 to 120 Hz
AC input voltage/current 220 to 240 V, 50 – 60 Hz, 0.8 A
Power consumption
Power consumption
Max. 95 W
Dimensions
Approx. 356
× 378 × 388 mm (w/h/d)
(14
1
/
8
× 15 × 15
3
/
8
inches)
Mass
Approx. 15 kg (33 lb 1 oz)
Plug and Play
DDC2B
Supplied accessories
* Recommended horizontal and vertical timing condition
• Horizontal sync width should be more than 1.0 µsec.
• Horizontal blanking width should be more than 3.6 µsec.
• Vertical blanking width should be more than 500 µsec.
• Horizontal blanking width should be more than 3.6 µsec.
• Vertical blanking width should be more than 500 µsec.
Design and specifications are subject to change without notice.
MENU
RESET
1 (power) indicator
MENU