Panasonic BT-3DL2550P User Manual
6
Read this first! (for BT-3DL2550E)
(continued)
EMC NOTICE FOR THE PURCHASER/USER OF THE
APPARATUS
1. Applicable standards and operating environment (BT-3DL2550E)
The apparatus is compliant with:
• standards EN55103-1 and EN55103-2 1996.11, and
• electromagnetic environments E1, E2, E3 and E4
• electromagnetic environments E1, E2, E3 and E4
2. Pre-requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as
peripheral equipment to be connected to the apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the
apparatus.
• Video signal connecting cables
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications,
for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended
for analog video signals.
for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended
for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications,
for analog audio signals.
Use shielded cables, which provide quality performance for high-frequency transmission applications,
for analog audio signals.
• Other connecting cables (IEEE1394, USB)
Use shielded cables, which provide quality performance for high-frequency applications, as
connecting cables.
connecting cables.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following
instructions in this manual.
• Use a sealed type cable (D-SUB 9 pin) for connecting to the GPI terminal.
3. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by
these standards.
these standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environ-
ment, such as an area where strong electromagnetic fields are generated (by the presence of signal trans-
mission towers, cellular phones, etc.). In order to minimize the adverse effects of the interference on the
apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being
affected and with its operating environment:
ment, such as an area where strong electromagnetic fields are generated (by the presence of signal trans-
mission towers, cellular phones, etc.). In order to minimize the adverse effects of the interference on the
apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being
affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other
appliances.
Pursuant to at the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
BT-3DL2550PE(VQT2U10)_E.book 6 ページ ２０１０年７月１２日 月曜日 午後１時４１分