Panasonic BT-3DL2550 User Manual
32
Main Menu
(continued)
Underlined values indicate factory defaults.
*1 When the monitor is shipped, settings for “USER1” - “USER5” are identical to “FACTORY.”
*2 “H SHIFT” (J page 24), “H POSITION”, “V POSITION”, “PHASE” and “CLOCK” (J page 41) cannot be saved
*2 “H SHIFT” (J page 24), “H POSITION”, “V POSITION”, “PHASE” and “CLOCK” (J page 41) cannot be saved
or loaded.
*3 So that there is no confusion with 2D mode when working in 3D mode, STATUS DISPLAY will display
information as per the “CONTINUE” setting even if “3SEC OFF” is selected.
SYSTEM CONFIG
Sub menu
Settings
Description
B.LIGHT/CONT.
BACKLIGHT
CONTRAST
Selects function to be assigned to BACKLIGHT/CONT. in the picture/
volume adjusting menu.
<BACKLIGHT> Adjusts the BACKLIGHT.
<CONTRAST>
volume adjusting menu.
<BACKLIGHT> Adjusts the BACKLIGHT.
<CONTRAST>
Adjusts the CONTRAST.
BACKLIGHT
0 - 50 - 60
Adjusts the backlight when the B.LIGHT/CONT. submenu is set to
CONTRAST.
CONTRAST.
MENU
POSITION
POSITION
CENTER
LB
RB
RT
LT
Positions the on-screen menu.
<CENTER>
<CENTER>
Center of the screen
<LB>
Left Bottom
<RB>
Right Bottom
<RT>
Right Top
<LT>
Left Top
STATUS
DISPLAY
DISPLAY
OFF
3SEC OFF *
3
CONTINUE
Sets display state for input signal status (on-screen menu).
<OFF>
<OFF>
Not displayed.
<3SEC OFF>
Displayed for 3 seconds after a status change.
<CONTINUE>
Displayed at all times
SETUP LOAD
USER5
*1*2
USER4
*1*2
USER3
*1*2
USER2
*1*2
USER1
*1*2
FACTORY
Loads saved factory defaults (FACTORY) or user data (USER1 - USER5).
After loading user data, the screen displays the signal selected before
user data was loaded.
After loading user data, the screen displays the signal selected before
user data was loaded.
SETUP SAVE
USER5
*2
USER4
*2
USER3
*2
USER2
*2
USER1
*2
Up to 5 sets of user data can be saved (J page 22).
They save menu settings and adjustments made in the picture/volume
adjusting menu (PHASE/CHROMA/BRIGHT/CONTRAST/BACKLIGHT)
except “SETUP SAVE/SETUP LOAD.”
They save menu settings and adjustments made in the picture/volume
adjusting menu (PHASE/CHROMA/BRIGHT/CONTRAST/BACKLIGHT)
except “SETUP SAVE/SETUP LOAD.”
POWER ON
SETUP
USER5
USER4
USER3
USER2
USER1
FACTORY
LAST
Selects the settings used when the power is turned on.
<LAST>
<LAST>
Starts in the mode used when the power was last turned
off.
off.
<FACTORY> Starts up using the factory defaults.
<USER1 - 5> Starts up using USER registered settings.
<USER1 - 5> Starts up using USER registered settings.
POWER SAVE
MODE
OFF
ON
Sets the power save mode
<OFF> Does not activate the POWER SAVE mode.
<ON> The backlight dims when no signal (NO SIGNAL) is input for 60
<OFF> Does not activate the POWER SAVE mode.
<ON> The backlight dims when no signal (NO SIGNAL) is input for 60
seconds or longer. Signal input or menu operation will return the
backlight to its normal brightness.
backlight to its normal brightness.
CALIBRATION
Connect a CA-210 color analyzer and use this submenu to make a
calibration. It also returns calibration data to factory defaults. (J page 33,
34)
calibration. It also returns calibration data to factory defaults. (J page 33,
34)
BT-3DL2550PE(VQT2U10)_E.book 32 ページ ２０１０年７月８日 木曜日 午後２時１２分