Cypress CY7C1420AV18 User Manual
CY7C1416AV18, CY7C1427AV18
CY7C1418AV18, CY7C1420AV18
CY7C1418AV18, CY7C1420AV18
Document Number: 38-05616 Rev. *F
Page 6 of 31
Pin Definitions
Pin Name
IO
Pin Description
DQ
[x:0]
Input Output-
Synchronous
Synchronous
Data Input Output Signals. Inputs are sampled on the rising edge of K and K clocks during valid write
operations. These pins drive out the requested data during a read operation. Valid data is driven out on
the rising edge of both the C and C clocks during read operations or K and K when in single clock mode.
When read access is deselected, Q
operations. These pins drive out the requested data during a read operation. Valid data is driven out on
the rising edge of both the C and C clocks during read operations or K and K when in single clock mode.
When read access is deselected, Q
[x:0]
are automatically tri-stated.
CY7C1416AV18
− DQ
[7:0]
CY7C1427AV18
− DQ
[8:0]
CY7C1418AV18
− DQ
[17:0]
CY7C1420AV18
− DQ
[35:0]
LD
Input-
Synchronous
Synchronous Load. This input is brought LOW when a bus cycle sequence is defined. This definition
includes address and read/write direction. All transactions operate on a burst of 2 data. LD must meet
the setup and hold times around edge of K.
includes address and read/write direction. All transactions operate on a burst of 2 data. LD must meet
the setup and hold times around edge of K.
NWS
0
,
NWS
1
Input-
Synchronous
Nibble Write Select 0, 1
− Active LOW (CY7C1416AV18 only). Sampled on the rising edge of the K
and K clocks during write operations. Used to select which nibble is written into the device during the
current portion of the write operations. Nibbles not written remain unaltered.
NWS
current portion of the write operations. Nibbles not written remain unaltered.
NWS
0
controls D
[3:0]
and NWS
1
controls D
[7:4]
.
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select
ignores the corresponding nibble of data and it is not written into the device.
ignores the corresponding nibble of data and it is not written into the device.
BWS
0
,
BWS
1
,
BWS
2
,
BWS
3
Input-
Synchronous
Byte Write Select 0, 1, 2, and 3
− Active LOW. Sampled on the rising edge of the K and K clocks during
write operations. Used to select which byte is written into the device during the current portion of the write
operations. Bytes not written remain unaltered.
CY7C1427AV18
operations. Bytes not written remain unaltered.
CY7C1427AV18
− BWS
0
controls D
[8:0]
CY7C1418AV18
− BWS
0
controls D
[8:0]
and BWS
1
controls D
[17:9].
CY7C1420AV18
− BWS
0
controls D
[8:0]
, BWS
1
controls D
[17:9]
, BWS
2
controls D
[26:18],
and BWS
3
controls
D
[35:27]
.
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select
ignores the corresponding byte of data and it is not written into the device.
ignores the corresponding byte of data and it is not written into the device.
A, A0
Input-
Synchronous
Address Inputs. These address inputs are multiplexed for both read and write operations. Internally, the
device is organized as 4M x 8 (2 arrays each of 2M x 8) for CY7C1416AV18, 4M x 9 (2 arrays each of
2M x 9) for CY7C1427AV18, 2M x 18 (2 arrays each of 1M x 18) for CY7C1418AV18, and 1M x 36 (2
arrays each of 512K x 36) for CY7C1420AV18.
CY7C1416AV18 – Since the least significant bit of the address internally is a “0,” only 21 external address
inputs are needed to access the entire memory array.
CY7C1427AV18 – Since the least significant bit of the address internally is a “0,” only 21 external address
inputs are needed to access the entire memory array.
CY7C1418AV18 – A0 is the input to the burst counter. These are incremented in a linear fashion internally.
21 address inputs are needed to access the entire memory array.
CY7C1420AV18 – A0 is the input to the burst counter. These are incremented in a linear fashion internally.
20 address inputs are needed to access the entire memory array. All the address inputs are ignored when
the appropriate port is deselected.
device is organized as 4M x 8 (2 arrays each of 2M x 8) for CY7C1416AV18, 4M x 9 (2 arrays each of
2M x 9) for CY7C1427AV18, 2M x 18 (2 arrays each of 1M x 18) for CY7C1418AV18, and 1M x 36 (2
arrays each of 512K x 36) for CY7C1420AV18.
CY7C1416AV18 – Since the least significant bit of the address internally is a “0,” only 21 external address
inputs are needed to access the entire memory array.
CY7C1427AV18 – Since the least significant bit of the address internally is a “0,” only 21 external address
inputs are needed to access the entire memory array.
CY7C1418AV18 – A0 is the input to the burst counter. These are incremented in a linear fashion internally.
21 address inputs are needed to access the entire memory array.
CY7C1420AV18 – A0 is the input to the burst counter. These are incremented in a linear fashion internally.
20 address inputs are needed to access the entire memory array. All the address inputs are ignored when
the appropriate port is deselected.
R/W
Input-
Synchronous
Synchronous Read or Write Input. When LD is LOW, this input designates the access type (read when
R/W is HIGH, write when R/W is LOW) for loaded address. R/W must meet the setup and hold times
around edge of K.
R/W is HIGH, write when R/W is LOW) for loaded address. R/W must meet the setup and hold times
around edge of K.
C
Input Clock
Positive Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. Use the C and C together to deskew the flight times of various devices on the board back to
the controller. See
the device. Use the C and C together to deskew the flight times of various devices on the board back to
the controller. See
on page 9 for further details.
C
Input Clock
Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. Use the C and C together to deskew the flight times of various devices on the board back to
the controller. See
the device. Use the C and C together to deskew the flight times of various devices on the board back to
the controller. See
on page 9 for further details.
K
Input Clock
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q
and to drive out data through Q
[x:0]
when in single clock mode. All accesses are initiated on the rising
edge of K.
K
Input Clock
Negative Input Clock Input. K is used to capture synchronous data being presented to the device and
to drive out data through Q
to drive out data through Q
[x:0]
when in single clock mode.