Pioneer PDA-5004 User Manual
26
En
English
Operation
Automatic power-off
(POWER MANAGEMENT)
(POWER MANAGEMENT)
The plasma display is equipped with [POWER
MANAGEMENT] and [AUTO POWER OFF] functions;
when set, the function automatically switches the unit to
either standby mode or power off mode whenever a sync
signal is not detected (a warning message is displayed on
the screen before the functions operate).
MANAGEMENT] and [AUTO POWER OFF] functions;
when set, the function automatically switches the unit to
either standby mode or power off mode whenever a sync
signal is not detected (a warning message is displayed on
the screen before the functions operate).
Notes
÷ [POWER MANAGEMENT] settings are supported only when a
÷ [POWER MANAGEMENT] settings are supported only when a
computer signal is input to INPUT 1 or INPUT 5 (PDA-5003
only), or when INPUT2 is selected.
only), or when INPUT2 is selected.
÷ The auto-power-off function can be used only in those cases
other than the inputs used in the preceding item.
÷ Always turn off the plasma display’s main power switch when
not using the display for extended periods of time.
INPUT
MENU
SET
2/3
1
Press the MENU button to display the menu screen.
MENU
INPUT1
PICTURE
SCREEN
SETUP
OPTION
:
0
:
0
:
0
:
0
:
0
:
0
CONTRAST
:
0
BRIGHTNESS
R.LEVEL
G.LEVEL
B.LEVEL
H.ENHANCE
V.ENHANCE
R.LEVEL
G.LEVEL
B.LEVEL
H.ENHANCE
V.ENHANCE
PICTURE RESET
2
Use the
2/3 buttons to select [SETUP].
[When computer signal is input to INPUT1 or
INPUT5 (PDA-5003 only), or when INPUT2 is used]
INPUT5 (PDA-5003 only), or when INPUT2 is used]
: V G A
:
:
:
SIGNAL FORMAT
CLAMP POSITION
:
AUTO
POWER MANAGEMENT
OFF
MENU
INPUT1
PICTURE
SCREEN
SETUP
OPTION
[In all other cases]
SET
MENU
:
:
:
DNR
COLOR TEMP.
:
MIDDLE
MIDDLE
MIDDLE
:
:
:
COLOR SYSTEM
PURECINEMA
OFF
AUTO
AUTO
:
:
:
CTI
ON
MPEG NR
LOW
AUTO POWER OFF
DISABLE
MENU
INPUT3
PICTURE
SCREEN
SETUP
OPTION
CHANGE
EXIT
3
Press the SET button to confirm selection of the
[POWER MANAGEMENT] or [AUTO POWER OFF].
The factory default setting is [OFF/DISABLE].
Each time the button is pressed, the setting alternates
as follows:
[POWER MANAGEMENT] or [AUTO POWER OFF].
The factory default setting is [OFF/DISABLE].
Each time the button is pressed, the setting alternates
as follows:
÷ OFF/DISABLE.....
The display will continue in operating mode,
regardless of the presence/absence of an input sync
signal.
regardless of the presence/absence of an input sync
signal.
÷ POWER MANAGEMENT: ON.....
If a sync signal is not detected, a warning message is
first displayed for 8 seconds, after which the display
automatically enters the standby mode, and the ON
indicator flashes green. If a sync signal (*1) is input
again later, the plasma display automatically returns to
normal operating mode.
first displayed for 8 seconds, after which the display
automatically enters the standby mode, and the ON
indicator flashes green. If a sync signal (*1) is input
again later, the plasma display automatically returns to
normal operating mode.
*1 Except when input signal is G ON SYNC or composite
SYNC.
÷ AUTO POWER OFF: ENABLE.....
If no sync signal is detected for 8 minutes or more, a
warning message will be displayed for 30 seconds,
after which the display’s power will switch to power off
mode.
warning message will be displayed for 30 seconds,
after which the display’s power will switch to power off
mode.
4
When the setup is finished, press the MENU
button to exit the menu screen.
button to exit the menu screen.
Note
The [POWER MANAGEMENT] and [AUTO POWER OFF]
functions must be set individually for each input (INPUT1 to
The [POWER MANAGEMENT] and [AUTO POWER OFF]
functions must be set individually for each input (INPUT1 to
INPUT5).
To return to operating mode:
÷ To return to normal operation from the [POWER
MANAGEMENT] function’s standby mode, either operate
your computer, or press the INPUT button on the plasma
display or remote control unit.
your computer, or press the INPUT button on the plasma
display or remote control unit.
÷ To return to normal operation from the [AUTO POWER
OFF] function’s power off condition, press the STANDBY/
ON button on the plasma display or on the remote control
unit.
ON button on the plasma display or on the remote control
unit.
Operation
MENU
SET
2/3
INPUT
Remote control unit
Display operating
panel
panel
3 OFF/DISABLE
ON/ENABLE
2