Freescale Semiconductor MC68HC908MR16 User Manual
Serial Peripheral Interface Module (SPI)
MC68HC908MR32 • MC68HC908MR16 Data Sheet, Rev. 6.1
200
Freescale Semiconductor
The clock phase (CPHA) control bit selects one of two fundamentally different transmission formats. The
clock phase and polarity should be identical for the master SPI device and the communicating slave
device. In some cases, the phase and polarity are changed between transmissions to allow a master
device to communicate with peripheral slaves having different requirements.
clock phase and polarity should be identical for the master SPI device and the communicating slave
device. In some cases, the phase and polarity are changed between transmissions to allow a master
device to communicate with peripheral slaves having different requirements.
NOTE
Before writing to the CPOL bit or the CPHA bit, disable the SPI by clearing
the SPI enable bit (SPE).
the SPI enable bit (SPE).
15.5.2 Transmission Format When CPHA = 0
shows an SPI transmission in which CPHA is logic 0. The figure should not be used as a
replacement for data sheet parametric information.Two waveforms are shown for SPSCK: one for
CPOL = 0 and another for CPOL = 1. The diagram may be interpreted as a master or slave timing
diagram since the serial clock (SPSCK), master in/slave out (MISO), and master out/slave in (MOSI) pins
are directly connected between the master and the slave. The MISO signal is the output from the slave,
and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The
slave SPI drives its MISO output only when its slave select input (SS) is at logic 0, so that only the selected
slave drives to the master. The SS pin of the master is not shown but is assumed to be inactive. The SS
pin of the master must be high or must be reconfigured as general-purpose I/O not affecting the SPI. (See
CPOL = 0 and another for CPOL = 1. The diagram may be interpreted as a master or slave timing
diagram since the serial clock (SPSCK), master in/slave out (MISO), and master out/slave in (MOSI) pins
are directly connected between the master and the slave. The MISO signal is the output from the slave,
and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The
slave SPI drives its MISO output only when its slave select input (SS) is at logic 0, so that only the selected
slave drives to the master. The SS pin of the master is not shown but is assumed to be inactive. The SS
pin of the master must be high or must be reconfigured as general-purpose I/O not affecting the SPI. (See
.) When CPHA = 0, the first SPSCK edge is the MSB capture strobe. Therefore,
the slave must begin driving its data before the first SPSCK edge, and a falling edge on the SS pin is used
to start the slave data transmission. The slave’s SS pin must be toggled back to high and then low again
between each byte transmitted as shown in
to start the slave data transmission. The slave’s SS pin must be toggled back to high and then low again
between each byte transmitted as shown in
.
Figure 15-5. Transmission Format (CPHA = 0)
Figure 15-6. CPHA/SS Timing
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
LSB
MSB
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
LSB
MSB
1
2
3
4
5
6
7
8
SPSCK CYCLE #
FOR REFERENCE
SPSCK, CPOL = 0
SPSCK, CPOL = 1
MOSI
FROM MASTER
MISO
FROM SLAVE
SS, TO SLAVE
CAPTURE STROBE
BYTE 1
BYTE 3
MISO/MOSI
BYTE 2
MASTER SS
SLAVE SS
CPHA = 0
SLAVE SS
CPHA = 1