Panasonic DP-180 User Manual
12
Getting To Know Your Machine
Installation
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13
amps and that it is approved by ASTA or BSI to BS1362
Check for the ASTA mark
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13
amps and that it is approved by ASTA or BSI to BS1362
Check for the ASTA mark
or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR
OFFICE
THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF
SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green and Yellow : Earth
Blue
replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR
OFFICE
THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF
SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green and Yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the main lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug
which is marked by letter E or by the safety Earth symbol “
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug
which is marked by letter E or by the safety Earth symbol “
“ or coloured GREEN or GREEN-
AND-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
The wire which is coloured BLUE must be connected to the
terminal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and replace
the fuse.
Open the fuse compartment with a screwdriver and replace
the fuse.
Precautions
For U.K.
Handling
■ Do not turn the Power Switch Off or open the Front Cover during copying/printing.
■ Energy Saver Mode Notice
● The following functions will not work if the Energy Saver Mode setting is set to the Shutdown
mode.
When using any of the following functions, we recommend that you leave the Energy Saver
Mode in the initial factory default setting (Sleep mode). (See page 36)
• Printer Function (USB Local and Network Connections)
• Internet Fax/Email Function
• Facsimile Function
When the LAN cable is not connect and DHCP DEFAULT is "VALID" (See page 37)
When using any of the following functions, we recommend that you leave the Energy Saver
Mode in the initial factory default setting (Sleep mode). (See page 36)
• Printer Function (USB Local and Network Connections)
• Internet Fax/Email Function
• Facsimile Function
When the LAN cable is not connect and DHCP DEFAULT is "VALID" (See page 37)
N