Multi-Tech Systems ISI5634UPCI User Manual

Chapter 3 – Software Installation 

36

 

1.  This driver retains the standard serial device properties: dial-in port files (named in the form "ttyMUxy"), and 

call-out port files (named in the form "cumxy"). File names of these two special types become associated 
with each serial port. The first file type is for the dial-in port and has a name of the form "ttyMUxy" where 
the "x" denotes the card number and the final "y" denotes the port number on that card. The second file 
type is for the call-out port and has a name of the form "cumxy" where, again, the "x" denotes the card 
number and the "y" denotes the port number on that card. 

2.  Consider the situation of installing two 8-port Modem Cards in the server computer. In that case, the driver 

would create TTY devices "ttyMUla" to "ttyMUlh" and devices "cumla" to "cumlh" under the "/dev" 
directory for card 1. Similarly, devices ttyMU2a to ttyMU2h and devices "cum2a" to "cum2h" would be 
created for card 2. (If a 4-port card were installed as card 1, the driver would create TTY devices "ttyMUla" to 
"ttyMUld.") 

1.  To confirm the successful loading of the driver, execute the command "lsmod". The driver "mtsi_upci" 

should be listed in the list of modules. If the driver is not listed, invoke the "lsmod" command again and 
watch for errors. 

2.  Check that the tty devices (with names of the form "ttyMUxy") are listed under the /dev directory. If the tty 

devices are not listed, invoke the ". /mknod_script" command again (it was previously run as part of the 
"make install" script in step 7 of the "Building the Linux Driver" procedure) and watch for errors. 

3. To confirm that the tty devices function for each modem on the ISI Card, execute the utility "minicom" and 

dial out on each modem. 

1.  Run the "make clean" script. You must run this command from the "mtsi_upci_driver" directory. 

2.  The "make clean" script will delete the "resetport" and "mtsi_upci.o" files. 

3.  Run the "make uninstall" script. 

4.  You must run this command from the "mtsi_upci_driver" directory. The "make clean" script will remove the 

module "mtsi_upci". 

5.  Execute the "lsmod" command. The "mtsi_upci" module should no longer be listed. If this module is still 

listed, then invoke the command "rmmod mtsi_upci" and check again to see whether or not the module 
is listed. 

6.  Delete serial ports (these are files with names of the form "ttyMUxy"). 

7.  To do so, go to the "dev" directory. 

8.  Enter the command "rm ttyMUZ". 

For the Modem Cards, the port-reset utility allows you to reset ports without rebooting.  For the modem cards, the 
port-reset utility allows you to reset both ports and modems without rebooting. 

To reset a serial port, the DTR pin is set to the low logic level for one second. To reset the modem port, the 
Reset pin is toggled (i.e., its logic state is inverted and then restored). 

1.  To reset the port (for serial card) or modem (for modem card) run the command "resetport /dev/ttyMUxy" 

(where 'x' stands for card number and 'y' for the port number). 

2.  On the Modem Cards, the DTRLED will toggle indicating that the reset has occurred and this toggling might be 

observable on the modem attached to the port (if the modem is equipped for this indication). There is no 
similar indication of successful reset on the modem cards.