Black Box 3600 MODEM User Manual
Fax Operation
Modem 3600
9-9
HDLC Transmit +FTH=(Mod)
+FTH=(Mod)
causes the modem to transmit HDLC framed data using
the modulation and speed selected with the (Mod) parameter. For V.27
ter, V.29, and V.17 modulations, the modem will first transmit the
required training sequence (with echo protector tone). Configured for
HDLC transmission, the modem transmits HDLC flags and returns the
CONNECT result code. HDLC flags will continue to be sent until the
first byte of data is received from the DTE or until 5 seconds elapses
with no data. For more information, refer to the Class 1 specification.
ter, V.29, and V.17 modulations, the modem will first transmit the
required training sequence (with echo protector tone). Configured for
HDLC transmission, the modem transmits HDLC flags and returns the
CONNECT result code. HDLC flags will continue to be sent until the
first byte of data is received from the DTE or until 5 seconds elapses
with no data. For more information, refer to the Class 1 specification.
HDLC Receive +FRH=(Mod)
The command +FRH=(Mod) causes the modem to receive HDLC
framed data using the modulation and speed selected with the (Mod)
parameter. If the selected carrier is detected, a CONNECT result code is
sent to the DTE; if a different signal is detected, the modem sends a
+FCERROR (CONNECT ERROR) result code and returns to
command mode. This command will be aborted if the DTE sends any
character to the modem other than DC1 or DC3 during this mode. For
additional information, consult the Class 1 specification.
framed data using the modulation and speed selected with the (Mod)
parameter. If the selected carrier is detected, a CONNECT result code is
sent to the DTE; if a different signal is detected, the modem sends a
+FCERROR (CONNECT ERROR) result code and returns to
command mode. This command will be aborted if the DTE sends any
character to the modem other than DC1 or DC3 during this mode. For
additional information, consult the Class 1 specification.
Test Supported Range of Values +FTx=?, +FRx=?
The supported range of values for any of the fax transmit or receive
commands can be determined with the +FTx=? or +FRx=? command
where x is M, H, or S. The normal transmit and receive capabilities are
interrogated with +FTM=? and +FRM=?, while the HDLC transmit and
receive capabilities are interrogated with +FTH=? and +FRH=?. Since
the modem can send and receive normal data or HDLC data at all valid
speeds up to 14,400 bps, the modem returns the information text 3, 24,
48, 72, 73, 74, 96, 97, 98, 121, 122, 145, 146 for any of these four
commands if x is M or H. For the commands +FTS=? or +FRS=? the
modem returns the information text 0-255, indicating an allowed time
interval from 0 to 2.55 seconds. The appropriate information text is
always preceded and followed by <CR><LF> and followed by an
appropriate result code response.
commands can be determined with the +FTx=? or +FRx=? command
where x is M, H, or S. The normal transmit and receive capabilities are
interrogated with +FTM=? and +FRM=?, while the HDLC transmit and
receive capabilities are interrogated with +FTH=? and +FRH=?. Since
the modem can send and receive normal data or HDLC data at all valid
speeds up to 14,400 bps, the modem returns the information text 3, 24,
48, 72, 73, 74, 96, 97, 98, 121, 122, 145, 146 for any of these four
commands if x is M or H. For the commands +FTS=? or +FRS=? the
modem returns the information text 0-255, indicating an allowed time
interval from 0 to 2.55 seconds. The appropriate information text is
always preceded and followed by <CR><LF> and followed by an
appropriate result code response.