Roland Fantom-S88 User Manual
70
Creating a Rhythm Set
Changing How a Rhythm Tone Is
Sounded (WMT)
The WMT (Wave Mix Table) uses key velocity to control the four
waveforms assigned to the rhythm tone.
waveforms assigned to the rhythm tone.
fig.04-12a_50
For details on the setting, refer to
Wave Coarse Tune
Adjusts the pitch of the waveform’s sound up or down in semitone
steps (+/-4 octaves).
steps (+/-4 octaves).
Value:
-48– +48
The Coarse Tune of the entire rhythm tone is set by the Tone
Coarse parameter (p. 71).
Coarse parameter (p. 71).
Wave Fine Tune
Adjusts the pitch of the waveform’s sound up or down in 1-cent
steps (+/-50 cents).
steps (+/-50 cents).
Value:
-50– +50
One cent is 1/100th of a semitone.
The Fine Tune of the entire rhythm tone is set by the Tone Fine
Tune parameter (p. 71).
Tune parameter (p. 71).
Wave Level
You can set the volume of the waveform.
Value:
0–127
The volume level of each rhythm tone is set with the Tone Level
parameter; the volume levels of the entire rhythm set is set with
the Rhythm Level parameter (p. 67).
parameter; the volume levels of the entire rhythm set is set with
the Rhythm Level parameter (p. 67).
Wave Pan
This specifies the pan of the waveform. “L64” is far left, “0” is center,
and “63R” is far right.
and “63R” is far right.
Value:
L63–0–63R
WMT Velocity Control (Velocity Control Switch)
WMT Velocity Control determines whether a different rhythm tone
is played (ON) or not (OFF) depending on the force with which the
key is played (velocity).
is played (ON) or not (OFF) depending on the force with which the
key is played (velocity).
When set to “RND,” the rhythm set’s constituent rhythm tones will
sound randomly, regardless of any Velocity messages.
sound randomly, regardless of any Velocity messages.
Value:
OFF, ON, RANDOM
Wave Rnd Pan Sw (Wave Random Pan Switch)
Use this setting to cause the waveform’s panning to change
randomly each time a key is pressed (ON) or not (OFF).
randomly each time a key is pressed (ON) or not (OFF).
Value:
OFF, ON
The range of the panning change is set by the Rnd Pan Depth
parameter (p. 74).
parameter (p. 74).
Wave Alter Pan Sw (Wave Alternate Pan Switch)
This setting causes panning of the waveform to be alternated
between left and right each time a key is pressed. Set Alternate Pan
Switch to “ON” to pan the Wave according to the Alter Pan Depth
parameter (p. 74) settings, or to “REV” when you want the panning
reversed. If you do not want the panning to change each time a key
is pressed, set this to “OFF.”
between left and right each time a key is pressed. Set Alternate Pan
Switch to “ON” to pan the Wave according to the Alter Pan Depth
parameter (p. 74) settings, or to “REV” when you want the panning
reversed. If you do not want the panning to change each time a key
is pressed, set this to “OFF.”
Range
: OFF, ON, REV
Velo Fade Lower (Velocity Fade Width Lower)
This Determines what will happen to the tone’s level when the tone
is played at a velocity lower than its specified velocity range. Higher
settings produce a more gradual change in volume. If you want
notes played outside the specified key velocity range to not be
sounded at all, set this to “0.”
is played at a velocity lower than its specified velocity range. Higher
settings produce a more gradual change in volume. If you want
notes played outside the specified key velocity range to not be
sounded at all, set this to “0.”
Value:
0–127
Velo Range Lower (Velocity Range Lower)
This sets the lowest velocity at which the waveform will sound.
Make these settings when you want different waveforms to sound in
response to notes played at different strengths.
Make these settings when you want different waveforms to sound in
response to notes played at different strengths.
Value:
1–UPPER
Velo Range Upper (Velocity Range Upper)
This sets the highest velocity at which the waveform will sound.
Make these settings when you want different waveforms to sound in
response to notes played at different strengths.
Make these settings when you want different waveforms to sound in
response to notes played at different strengths.
Value:
LOWER–127
If you attempt to set the Lower velocity limit above the Upper, or
the Upper below the Lower, the other value will automatically
be adjusted to the same setting.
the Upper below the Lower, the other value will automatically
be adjusted to the same setting.
1
2
3
4
Reference_e.book 70 ページ ２００３年７月１４日 月曜日 午後３時２５分