Sharp PNH701 User Manual

4

E

•  This product is for use indoors.

•  A mounting bracket compliant with VESA specifications is 

required.

•  Since the monitor is heavy, consult your dealer before 

installing, removing or moving the monitor.

•  Mounting the monitor on the wall requires special expertise 

and the work must be performed by an authorized SHARP 

dealer. You should never attempt to perform any of this work 

yourself. Our company will bear no responsibility for accidents 

or injuries caused by improper mounting or mishandling.

•  Use the monitor with the surface perpendicular to a level 

surface. If necessary, the monitor may be tilted up to 20 

degrees upward or downward. 

•  This monitor should be used at an ambient temperature 

between 32°F (0°C) and 104°F (40°C). Provide enough space 

around the monitor to prevent heat from accumulating inside.

7-7/8 [200]

2 [50]

2

[50]

2

[50]

Unit: inch [mm]

Unit: inch [mm]

1-3/8 [35]

2 [50]

7-7/8 [200]

2

[50]

2

[50]

1-3/8 [35]

Power LED

•  If it is difficult to provide sufficient space for any reason such 

as the installation of the monitor inside a housing, or if the 

ambient temperature may be outside of the range of 32°F 

(0°C) to 104°F (40°C), install a fan or take other measures to 

keep the ambient temperature within the required range.

•  Temperature condition may change when using the monitor 

together with the optional equipments recommended by 

SHARP. In such cases, please check the temperature 

condition specified by the optional equipments.

•  Do not block any ventilation openings. If the temperature 

inside the monitor rises, this could lead to a malfunction.

•  Do not place the monitor on a device which generates heat.

•  Adhere to the following when installing the monitor in its 

portrait orientation. Failing to adhere to the following may 

cause malfunctions. 

-  Install the monitor such that the power LED is located on 

the bottom side.

- Set the MONITOR on the MONITOR menu to PORTRAIT.

(See OPERATION MANUAL.)

•  When installing the monitor in the portrait orientation, and 

the internal temperature of the monitor rises excessively, 

the brightness of the backlight automatically decreases in 

order to prevent a further temperature rise.

•  Use the supplied sticker.

  For the monitor in landscape orientation

Horizontal sticker 

(Logo)

  For the monitor in portrait orientation

Vertical sticker 

(Operation panel)

Be careful not to cover the remote control sensor or buttons.

-  Do not use the monitor where there is a lot of dust, where humidity 

is high, or where the monitor may come into contact with oil or 

steam. Do not use in an environment where there are corrosive 

gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, 

ammonia, ozone, etc.). As this could lead to fire.

-  Ensure that the monitor does not come into contact with water 

or other fluids. Ensure that no objects such as paper clips or 

pins enter the monitor as this could lead to fire or electric shock.

-  Do not place the monitor on top of unstable objects or in 

unsafe places. Do not allow the monitor to receive strong 

shocks or to strongly vibrate. Causing the monitor to fall or 

topple over may damage it.

-  Do not use the monitor near heating equipment or in places 

where there is likelihood of high temperature, as this may 

lead to generation of excessive heat and outbreak of fire.

-  Do not use the monitor in places where it may be exposed to 

direct sunlight.

-  Please be sure to constantly remove dust and garbage that 

has attached to the ventilation opening. If dust collects in the 

ventilation opening or the inside of the monitor, it may lead to 

excessive heat, outbreak of fire, or malfunction. 

Please request a cleaning of the inside of the monitor from 

an authorized SHARP servicing dealer or service center.

-  The AC outlet shall be installed near the equipment and shall 

be easily accessible.

- Use only the power cord supplied with the monitor.
-  Do not damage the power cord nor place heavy objects on 

it, stretch it or over bend it. Also, do not add extension cords. 

Damage to the cord may result in fire or electric shock.

-  Do not use the power cord with a power tap. 

Adding an extension cord may lead to fire as a result of 

overheating.

-  Do not remove or insert the power plug with wet hands. 

Doing so could result in electric shock.

- Unplug the power cord if it is not used for a long time.
-  Do not attempt to repair the power cord if it is broken 

or malfunctioning. Refer the servicing to the service 

representative.