Panasonic WV-CU650 User Manual
25
■ Database Copy
You can copy the database from the source system con-
troller (CONTROLLER NO. switch is set to 1.) to destination
system controllers (CONTROLLER NO. switch is set to 2 to
8.). When using two or more system controllers in the sys-
tem, you can copy the following settings.
troller (CONTROLLER NO. switch is set to 1.) to destination
system controllers (CONTROLLER NO. switch is set to 2 to
8.). When using two or more system controllers in the sys-
tem, you can copy the following settings.
• Administrator password
• Button functions and joystick button functions
• Button functions and joystick button functions
(F1 to F8, A, B, and top buttons)
• Controller functions
(Time & Date Type)
(Auto Login)
(Operator Setup)
(Function Level)
(Camera Level)
(Cam Posi Map)
(Cam-Unit Map)
(HDD-Unit Map)
(LCD Title)
(Auto Login)
(Operator Setup)
(Function Level)
(Camera Level)
(Cam Posi Map)
(Cam-Unit Map)
(HDD-Unit Map)
(LCD Title)
Notes:
• Database copy to two or more system controllers is
available at a time.
• To activate this mode, you need to perform the PS·Data
communication settings. (Refer to p. 20 PS·Data
Communication Setting.)
Communication Setting.)
• This function is available only among WV-CU650
System Controllers. You cannot copy the PS·Data data-
base to other models, such as WV-CU360C.
base to other models, such as WV-CU360C.
● Operation
1. Turn off the power of source and destination system
controllers.
2. Disconnect the system units from source and
destination system controllers.
3. Connect system controllers with modular cables.
4. Set the MODE switches of source and destination
system controllers to “PS·Data” mode.
5. Set the CONTROLLER NO. switch of source system
controller to “1”, and that of destination system
controllers to “2” to “8”.
(Refer to p. 18 CONTROLLER NO. Switch Setting.)
Note: Set a unique number for each system controller
controllers to “2” to “8”.
(Refer to p. 18 CONTROLLER NO. Switch Setting.)
Note: Set a unique number for each system controller
to avoid conflict.
6. Turn on the power of destination system controller.
Login is not required.
7. Turn on the power of source system controller while
holding down the button 2 and MON (ESC) buttons.
“Admin Password” will appear on the LCD to enter the
password.
“Admin Password” will appear on the LCD to enter the
password.
8. Enter the administrator password.
The password entered will be displayed as “
∗” marks.
Note: The factory default is “650”.
9. Press the CAM (SET) button.
If the password entered is correct, the LCD display of
source system controller becomes as follows.
source system controller becomes as follows.
The LCD display of destination system controller(s)
become(s) as follows.
become(s) as follows.
10. Press the CAM (SET) button of the source system
controller.
The database copy will be started, and the LCD display
of source system controller becomes as follows.
The database copy will be started, and the LCD display
of source system controller becomes as follows.
The LCD display of destination system controller(s)
become(s) as follows.
become(s) as follows.
11. When the copy has been completed, the check sum
(SUM=nnnn) appears on the LCD of each system
controller.
When the copy has been successfully completed, the
check sum is identical to each other.
controller.
When the copy has been successfully completed, the
check sum is identical to each other.
The LCD display of source system controller becomes
as follows.
as follows.
Data Base Tx Mode
“Enter SET Button”
Data Base Rx Mode
Data Base Tx Mode
Completed 60%
Data Base Rx Mode
Completed 60%
Data Base Tx Mode
Completed Sum=1733
Data Base Copy Mode
Admin Password _____
Data Base Copy Mode
Admin Password
∗ ∗ ∗ ∗ ∗