TP-LINK TF-3239D Leaflet
2
Ø
Supports ACPI, PCI power management
Ø
Complies with the IEEE802.3u Fast Ethernet, 100Base-TX
standard and IEEE802.3 CSMA/CD 10Base-T standard
Ø
Supports Full Duplex Flow Control (IEEE 802.3x)
Ø
Full duplex design to double the performance
Ø
Supports Auto-Negotiation function
Ø
Auto-setups IRQ and I/O address
Ø
Contains two large (2Kbyte) independent receive and transmit
FIFOs
Ø
One STP/UTP connector for 10Mbps or 100Mbps network Speed
Ø
Provides diagnostic software and one LED to indicate network
Link/activity
Ø
Supports smart remote boot ROM and provides the help for
RPL/PXE(Exclude TF-3239DL)
Ø
Supports ODI Driver for NetWare 3.x, 4.x, NDIS Driver for LAN
Manager, Windows 95, Windows NT, Windows 2000, Packet
driver for TCP/IP
Chapter 2 Installation
Card Installation
To insert The Product into your computer, follow the steps list below.
1 Turn off the computer and remove its cover.
2 Insert The Product into a PCI slot.
3
Secure the Product to the rear of the computer chassis and put
back the computer cover.
4 Connect the Product to the network using twisted-pair cables.
Driver Installation
Use the drivers supplied by the diskette included in The Product. For
detail description, please refer to "help" in the diskette provided by the
Product.
Appendix A: Troubleshooting
If you experience any problems with the adapter, first make sure the
appropriate driver is loaded, the proper cable is connected to the
adapter port and the hub complies with the adapter specification, such
as 10Mbps 10Base-T or 100Mbps 100Base-TX. Then recheck the LED.
The Product provided one LEDs to indicate network status.
LINK/ACTIVE LED
A red LED indicates if the 10 or 100Mbps STP/UTP has been link OK or
not and is working or not. When the light is OFF, it indicates that the
STP/UTP port has not been connected or link not OK; When the light
is ON, it indicates that the STP/UTP port link OK. When the light is
BLINKING, it indicates that the STP/UTP port is receiving data or
transmitting data.
Appendix B: Technical Specification
Topology: Star
Connector Supported: RJ45
Standard: IEEE802.3 10Base-T
IEEE802.3u 100Base-TX
Transmission Rate: 100Mbps or 200Mbps
Hardware: IBM PC compatibles(It must have PCI slot)
IRQ Line: Assigned by system
I/O Address: Assigned by system
Software: ODI driver for NetWare 3.x, 4.x, NDIS driver for Microsoft
LAN manager and Windows 98, Windows ME, Windows NT, Windows
2000 Packet driver for TCP/IP
o
o
Temperature: 0 C to 40 C (Operating)
Humidity: 5% to 95% (Non-condensing)
Power consumption: 1W(Max)
Appendix C: Contact Information
TP-LINK TECHNOLOGIES CO., LTD.
For help with the installation or operation of the TP-LINK TF-3239D/
TF-3239DL Adapter, please contact us.
Add: Fl.3, Bldg.R1-B, High-Tech Industrial Park, Shennan Road,
Shenzhen, China
E-mail: support@tp-link.com
Website: http://www.tp-link.com
4
3
5
User's Guide
10/100M Fast Ethernet Adapter
TF-3239D/TF-3239DL
7
1
0
3
0
4
2
9
Made in China
V
e
r:
2
.0