IBM CTI 2572 User Manual
CTI 2572 Technical Overview Manual
3
CHAPTER 2. LOCAL AREA NETWORK OVERVIEW
Local Area Networks (LANs) grew from the need to interconnect many intelligent devices in a
non-proprietary manner. Today, the most widely used LAN standards are Token-Ring (IEEE
802.5) and Ethernet (IEEE 802.3). Token Bus (IEEE 802.4), was proposed by GM in the late
80’s as a part of the Manufacturing Automation Protocol (MAP). Token Bus has seen limited
use, primarily due to cost and installation difficulty. It is briefly discussed in this document to
provide a more complete perspective of factory networking alternatives.
non-proprietary manner. Today, the most widely used LAN standards are Token-Ring (IEEE
802.5) and Ethernet (IEEE 802.3). Token Bus (IEEE 802.4), was proposed by GM in the late
80’s as a part of the Manufacturing Automation Protocol (MAP). Token Bus has seen limited
use, primarily due to cost and installation difficulty. It is briefly discussed in this document to
provide a more complete perspective of factory networking alternatives.
2.1 Master/Slave vs. Local Area Networks
Master/slave networks are commonly used in factory floor communications. These networks use
a master station (computer or /controller) and multiple slave devices (such as controllers,
terminals, or readers). The master station polls each slave unit on the network in turn, requesting
services or information. After the slave performs the task (or indicates that it cannot), the master
polls the next slave. This scheme works reasonably well when there are few devices on the
network. However, as the size of the network grows, more and more master processor resources
and network bandwidth must be devoted to the "overhead" of polling. This overhead limits
throughput and lengthens response time, especially since most master/slave networks operate at a
data rate of 115 K bits/sec or less.
a master station (computer or /controller) and multiple slave devices (such as controllers,
terminals, or readers). The master station polls each slave unit on the network in turn, requesting
services or information. After the slave performs the task (or indicates that it cannot), the master
polls the next slave. This scheme works reasonably well when there are few devices on the
network. However, as the size of the network grows, more and more master processor resources
and network bandwidth must be devoted to the "overhead" of polling. This overhead limits
throughput and lengthens response time, especially since most master/slave networks operate at a
data rate of 115 K bits/sec or less.
Local area networks (LANs), on the other hand, do not have a master station. All stations on the
network can initiate a message. Standard rules for media access determine when a given station
may send a message. Media access rules usually involve passing a token or listening for traffic
on the line. As a result, the overhead of a typical local area network is much lower than a
master/slave network. This characteristic, coupled with much higher signalling rates (10 - 16
Mb) provides much higher throughput and allows many more devices to be connected to the
network. Because there is no master station, there is no single point of failure.
network can initiate a message. Standard rules for media access determine when a given station
may send a message. Media access rules usually involve passing a token or listening for traffic
on the line. As a result, the overhead of a typical local area network is much lower than a
master/slave network. This characteristic, coupled with much higher signalling rates (10 - 16
Mb) provides much higher throughput and allows many more devices to be connected to the
network. Because there is no master station, there is no single point of failure.
Each master/slave network tends to use a different protocol, partially because there is no
generally accepted standard. The protocol is typically determined by the primary equipment
manufacturer and in some cases the protocol may be proprietary, subject to copyright or patent
laws. As a result, most master/slave networks have very poor multi-vendor inter-operability.
Conversely, LANs such as Ethernet and Token-Ring have protocols that are well specified and
documented by standards bodies such as IEEE and are supported by a wide number of vendors.
generally accepted standard. The protocol is typically determined by the primary equipment
manufacturer and in some cases the protocol may be proprietary, subject to copyright or patent
laws. As a result, most master/slave networks have very poor multi-vendor inter-operability.
Conversely, LANs such as Ethernet and Token-Ring have protocols that are well specified and
documented by standards bodies such as IEEE and are supported by a wide number of vendors.