Adtran 3100 Series Leaflet
Quick Start Guide, 61700600L2-13A, July 2006
Technical Support 1-888-4ADTRAN (1-888-423-8726)
Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at
.
Quick Start Guide
®
NetVanta 3100 Series Router
P/N 1700600L2, 1700610L2
STAT
ETH1
VPN
DBU
1
2
SWITCH
NetVanta 3120
3
4
NetVanta 3120 Front Panel Layout
G
ETTING
S
TARTED
Two configuration methods are available for your NetVanta router:
•
Web-based GUI
•
AOS Command Line Interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.
A
CCESS
THE
GUI
You may access the web-based GUI from any web browser on your network by following these
steps:
steps:
1.
Connect the router to your PC using one of the four switch ports on the back of the unit.
2.
During bootup your PC will obtain an IP address from the NetVanta 3100 Series unit’s DHCP
server. By default, both the DHCP and HTTP servers are enabled.
server. By default, both the DHCP and HTTP servers are enabled.
3.
Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.
4.
You will then be prompted for the username and password (the default settings are admin
and password).
and password).
5.
The initial GUI screen appears.
6.
Click on Getting Started in the System menu on the left side of your screen and follow the
on-line instructions.
on-line instructions.
C
ONFIGURE
THE
ATM PVC (N
ET
V
ANTA
3130 O
NLY
)
1.
Click on the Getting Started link under the System menu. This brings up a side bar page.
2.
Click on Step 1 - Configure the Public Interface at the top of the side bar page to open the
ATM PVC page.
ATM PVC page.
3.
Enter the PVC number and select an Interface Mode. Usually this is PPP or PPPoE;
however, if IP routing is chosen, you will need to enter an IP address.
however, if IP routing is chosen, you will need to enter an IP address.
4.
Click Apply. If PPP or PPPoE is selected as the Interface Mode, you will be taken to the
PPP page after clicking Apply. Here you will need to select the type of authentication
needed, authentication passwords, and the Address Type. In most cases you will want the
Address Type to be Negotiated. Click Apply when all the information is complete.
PPP page after clicking Apply. Here you will need to select the type of authentication
needed, authentication passwords, and the Address Type. In most cases you will want the
Address Type to be Negotiated. Click Apply when all the information is complete.
A
CCESS
THE
CLI
If needed, you can access the AOS CLI via a Telnet session.
1.
Telnet to the unit’s IP address. The default IP address is 10.10.10.1.
2.
You will then be prompted for the username and password (the default settings are admin
and password).
and password).
3.
Enter enable at the > prompt.
4.
Enter the enable password when prompted. The default password is password.
uy
For security purposes, you should set up an admin password
immediately. Use the Passwords page of the Web GUI to change this
password.
immediately. Use the Passwords page of the Web GUI to change this
password.
By default, the NetVanta 3130 comes with an ADSL and an Asynchronous
Transfer Mode (ATM) port already configured and enabled. The service
provider should provide a PVC (VPI/VCI) number which will be used to
configure the ATM PVC.
Transfer Mode (ATM) port already configured and enabled. The service
provider should provide a PVC (VPI/VCI) number which will be used to
configure the ATM PVC.
STAT
WAN
VPN
DBU
1
2
SWITCH
NetVanta 3130
3
4
NetVanta 3130 Front Panel Layout