Netcomm Gateway Series User Manual
8
SmartVoice Gateway(s) User Guide
YML83 Rev
•
FXO Hunting Default Dial-Out:
This will take effect as
FXO Hunting VoIP call in option is set to Default Dial-Out.
•
FXO Line VoIP call in options:
The usage of this option is as same as
FXO Hunting VoIP call in option. The Default Dial-Out
refers to individual lines rather than a hunting group. The individual FXO line default dial out
number can be set in Line configuration section as below.
number can be set in Line configuration section as below.
•
Enable: To enable a line; if some lines are not used, disable them (Pause Function) to avoid
unnecessary waiting when an incoming call is diverting to this line.
unnecessary waiting when an incoming call is diverting to this line.
Hotline Functions
•
FXS port: When the user picks up the phone, the gateway automatically dials your assigned hotline
number. When in hotline mode, other phone numbers cannot be dialed.
•
FXO port: When receiving a call from an outside line, the gateway will divert the call to the assigned
hotline number.
hotline number.
•
Hot Line No.: Enter the hot line number for automatic dialing function.
•
Warm Line: When the Warm Line function is in use, user can dial a number. Otherwise the system
will divert incoming calls from an outside line to the Hot Line Number after a set wait time.
will divert incoming calls from an outside line to the Hot Line Number after a set wait time.
Example:
Assume the assigned hotline for the SmartVoice Gateway line 3 is 701 and the Warm Line (Hot Line
Delay) is 5 seconds. If no extension number is dialed within 5 seconds, the call will be automatically
diverted to the assigned hotline (ext 701). The system allows users to record a voice prompt (e.g. “Please
enter an extension number or wait for the operator to connect you”) to use in this situation.
Delay) is 5 seconds. If no extension number is dialed within 5 seconds, the call will be automatically
diverted to the assigned hotline (ext 701). The system allows users to record a voice prompt (e.g. “Please
enter an extension number or wait for the operator to connect you”) to use in this situation.
Assume the assigned hotline for the SmartVoice Gateway line 4 is 70 and the wait time is 0 second.
When P4 receives a call from an outside line, it will be automatically diverted to extension 70.
When P4 receives a call from an outside line, it will be automatically diverted to extension 70.
•
Dial-out Prefix: It is the number dialed automatically by the system when the FXO interface diverts
a call to the PSTN by VoIP.
a call to the PSTN by VoIP.
•
FXO Line Default Dial-Out: Default number that FXO will dial out when it receive an incoming call
from VoIP.
from VoIP.
Example:
If PBX extension needs to dial “0” to make a PSTN call, and the FXO ports are connected to PBX
extension. In this case, the Dial-out prefix should be set to “0”. If the PBX requires some delay time
before capturing a line, then the trunk prefix should be set as “0,” so that after dialing a 0, it will pause
for 1 second before dialing the destination number. Each comma represents a 1 second delay. If more
delay time is required, simply add more commas. Please note that if a Dial-out prefix is set, the line won’t
be able to dial any PBX extension line (the FXS interface does not have a trunk prefix function).
extension. In this case, the Dial-out prefix should be set to “0”. If the PBX requires some delay time
before capturing a line, then the trunk prefix should be set as “0,” so that after dialing a 0, it will pause
for 1 second before dialing the destination number. Each comma represents a 1 second delay. If more
delay time is required, simply add more commas. Please note that if a Dial-out prefix is set, the line won’t
be able to dial any PBX extension line (the FXS interface does not have a trunk prefix function).