Golden Technologies HMI 575 User Manual
DIGITAL START ADDRESS SELECT
OPTION SELECT
DIGITAL INPUT LEDS
1
4
8
1
2
4
8
16
128
32
64
TEST
256
ON
1 2
4
3
6
5
7 8
10
9
DIGITAL INPUT
1 2
4
3
6
5
5
• Zero setting the working hours and number of times the lamp is switched on
To zero the hours of the lamp’s life (“Bulb hours”) and the number of times it is
switched on (“Bulb strikes”) which are stored in the DMX Receiver microprocessor,
proceed as follows:
switched on (“Bulb strikes”) which are stored in the DMX Receiver microprocessor,
proceed as follows:
1. Set the TEST microswitch (27) to the ON position.
2. Shift the option 1 microswitch (32) from ON to OFF (or from OFF to ON) and vice
versa 3 times within a time of 6 seconds. If the procedure has been carried out
correctly, the three signal control LEDs (25) will light up simultaneously, while the
display (24) will go completely blank. This situation lasts for approximately
5 seconds.
correctly, the three signal control LEDs (25) will light up simultaneously, while the
display (24) will go completely blank. This situation lasts for approximately
5 seconds.
3. Return the TEST microswitch (27) to the OFF position.
29
30
31
29
• Changing the lamp
Open the re-lamping cover, loosen
the two side ring nuts (29) of the lamp
to be replaced and remove it from its
mountings (30).
Take the new lamp out of its package,
loosen the two side ring nuts (29) and
insert the lamp in its mountings (30).
Finally, screw on the ring nuts.
the two side ring nuts (29) of the lamp
to be replaced and remove it from its
mountings (30).
Take the new lamp out of its package,
loosen the two side ring nuts (29) and
insert the lamp in its mountings (30).
Finally, screw on the ring nuts.
WARNING: Do not touch the lamp’s
bulb with bare hands. Should this
happen, clean the bulb with a cloth
soaked in alcohol and dry it with a
clean, dry cloth.
bulb with bare hands. Should this
happen, clean the bulb with a cloth
soaked in alcohol and dry it with a
clean, dry cloth.
IMPORTANT: To distribute the beam of
light uniformly, the lamp needs to be
positioned with the protrusion (31) visible
on the bulb outside the optical axis
of the projector. For this purpose it is
recommended to turn the protrusion
towards the top cover (18).
light uniformly, the lamp needs to be
positioned with the protrusion (31) visible
on the bulb outside the optical axis
of the projector. For this purpose it is
recommended to turn the protrusion
towards the top cover (18).
27
24
32
25
34
34
33
• Replacing colour filters
Find the filter to be replaced, grip it
between your fingers and push it towards
the movable point of anchorage (33) until
the filter comes out of the fixed points of
anchorage (34). Bend the filter outwards
and take it out. Insert the new filter into
the mobile point (33) and anchor it in the
two fixed points (34).
between your fingers and push it towards
the movable point of anchorage (33) until
the filter comes out of the fixed points of
anchorage (34). Bend the filter outwards
and take it out. Insert the new filter into
the mobile point (33) and anchor it in the
two fixed points (34).
Standard colour filters:
Red:
080301/005
Yellow: 080301/002
Violet:
Violet:
080301/004
Green: 080301/003
Orange: 080301/007
Blue:
Orange: 080301/007
Blue:
080301/001
Pink:
080301/006
35
36
• Replacing metal gobos
Find the gobo to be replaced and delicately press towards the anchorage points (35)
until the gobo comes out.
Take the selected replacement from the holder (36) on the dimmer/stopper/strobe plate.
To insert the new gobo, position it at the two points of anchorage (35) and, lightly
pressing it, slot it into the remaining points, verifying the levelness of the gobo in its
housing.
until the gobo comes out.
Take the selected replacement from the holder (36) on the dimmer/stopper/strobe plate.
To insert the new gobo, position it at the two points of anchorage (35) and, lightly
pressing it, slot it into the remaining points, verifying the levelness of the gobo in its
housing.
STANDARD GOBOS
• Lubrication of rotating gobos
To ensure that the rotating gobos
continue to operate smoothly, the
bearings should be lubricated with oil
every six months: use only Kernite
LUBE-K-AHT (code 164028/801).
Apply the oil using a syringe with a fine
needle.
Avoid over-lubricating, as excess oil could
be spattered during rotation.
continue to operate smoothly, the
bearings should be lubricated with oil
every six months: use only Kernite
LUBE-K-AHT (code 164028/801).
Apply the oil using a syringe with a fine
needle.
Avoid over-lubricating, as excess oil could
be spattered during rotation.
081311
081313
081318
081325
OPTIONAL GOBOS
081305
081307
081312
081314
081315
081317
081319
081320
081321
081324
ENGLISH