Lexmark 18L0042 Leaflet
CONTENTS:
Ink Dispensers
Cyan/Magenta/Yellow
3 x 24cc
1 Cap
Removal Tool
for Lexmark 18L0042 “83” Tri-Color Cartridge ONLY
1. Protect work surface.
Refilling your cartridge is a clean and simple job, but it is best to cover
your work area with newspaper or other scrap paper to protect from
accidental ink spills.
your work area with newspaper or other scrap paper to protect from
accidental ink spills.
2. Remove depleted color print cartridge from printer according
to printer manufacturer's instructions.
3. Lay cartridge on its side. Using the cap removal tool provided
in the kit, pry the blue cap off the cartridge body. See Fig. 1.
4. Remove the scabbard from the refill dispenser of the
color you wish to refill. Insert the filler tube into the corresponding
color compartment through either of the two fill holes. Determine
appropriate color chamber by following figure 2. Push the filler tube
into the absorbent material as far as it will go. Then draw it back out
about 1/4" (6.5mm). See Fig. 2
color compartment through either of the two fill holes. Determine
appropriate color chamber by following figure 2. Push the filler tube
into the absorbent material as far as it will go. Then draw it back out
about 1/4" (6.5mm). See Fig. 2
5. Tilt the bottle until the filler tube is in the fully inverted position
Fig. 3. Squeeze the bottle with moderate pressure and keep pressure
applied until you see ink appear at the top of the color compartment.
Immediately stop squeezing the bottle. Draw filler tube most of the
way out then release pressure on bottle and allow the refill bottle to
suck back any excess ink.
applied until you see ink appear at the top of the color compartment.
Immediately stop squeezing the bottle. Draw filler tube most of the
way out then release pressure on bottle and allow the refill bottle to
suck back any excess ink.
6. Bring the bottle back to the position shown in Fig. 2
(filler tube in horizontal position) and remove the filler tube.
Recap the ink bottle and save for future refills. Replace the cap on
the print cartridge. Inspect the print head and wipe off any excess ink
immediately to prevent possible contamination of print nozzles.
Recap the ink bottle and save for future refills. Replace the cap on
the print cartridge. Inspect the print head and wipe off any excess ink
immediately to prevent possible contamination of print nozzles.
7. Reinstall the cartridge into the printer.
If asked “Installing a new cartridge” or “Reinstalling a used cartridge,”
choose “Installing a new cartridge.” This will reset the ink level monitor
to read “Full.” Run a priming/cleaning cycle and print test following
the instructions included with your printer. It may be necessary to repeat
the print test several times to bring the color balance back to normal.
choose “Installing a new cartridge.” This will reset the ink level monitor
to read “Full.” Run a priming/cleaning cycle and print test following
the instructions included with your printer. It may be necessary to repeat
the print test several times to bring the color balance back to normal.
Fig.4
LX83RC 5/03
IF YOU HAVE ANY QUESTIONS OR ENCOUNTER ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE CONTACT:
Dispense ink
into selected
color chamber
into selected
color chamber
Fig. 3
Yellow
Cyan
Magenta
Magenta
Cyan
Yellow
Pry off cap with
tool supplied
tool supplied
Fig. 2
Fig. 1
665 State Highway 23 • Wayne, NJ 07470-6892 U.S.A. • (973) 696-3330 • (800) 288-3330
Fax: (973) 694-7287 • Email: help@repeatotype.com • www.repeatotype.com
Lexmark is a registered trademark of Lexmark International. Compaq is a trademark of Compaq Computer Co. Xerox is a trademark of Xerox Corp.
Sharp is a trademark of Sharp Electronics Corp. ©2003 Repeat-O-Type Manufacturing Corporation.
Refilling Instructions
Snap cap
back in place
back in place
MANUFACTURING CORPORATION
ESTABLISHED 1931