Epson NX300 User Manual
Choose your settings
Select your language:
1
Press Menu to enter the setup mode.
2
Press
or
to select Maintenance, then press OK.
3
Press
or
to select your Language,
then press OK.
4
Press
or
to select your laguage,
then press OK.
If anything is missing, contact Epson as described on the back
in “Any questions?”.
in “Any questions?”.
Caution: Do not open the ink cartridge package until you are ready to
install the ink. Cartridges are vacuum packed to maintain reliability.
Canada only: For French speakers, remove sticker(s) from the backing
Canada only: For French speakers, remove sticker(s) from the backing
sheet and place over corresponding text on the control panel.
Unpack
1
Start Here
2
Open the output tray, pull out the extension, and raise the paper
stopper.
stopper.
3
Slide the edge guide to the left while holding the feeder guard forward.
4
Load paper against the right edge guide and behind the tab, with the
printable side face up.
printable side face up.
Note: Don’t load the paper sideways;
always load it short edge first.
always load it short edge first.
5
Slide the edge guide over.
5
Insert the cartridges in the holder for each color.
6
Press each cartridge down until it clicks.
7
Close the ink cartridge cover and press it down until it clicks.
8
Close the scanner.
9
Press the OK button to charge the ink. Charging takes about 2 minutes.
Caution: Don’t turn off the NX300 Series while it is charging or you’ll
waste ink
waste ink
(Included for Canada only)
Epson Stylus
®
NX300 Series
1
Connect the power cable.
Caution: Do not connect to your computer yet.
2
Press the
On button.
Turn on the NX300 Series
2
Install ink cartridges
Note: Don’t load paper before installing the ink cartridges.
1
Open the scanner.
2
Open the cartridge cover.
3
Shake the ink cartridges,
then unpack them.
then unpack them.
4
Remove only the yellow tape from each
cartridge.
cartridge.
Caution: Don’t remove any other
seals from the cartridges.
seals from the cartridges.
3
Load paper
5
1
Open the paper support and pull up the extension.
To use the NX300 Series for faxing, connect the included phone cord from
a telephone wall jack to the LINE port on the NX300 Series. To connect a
telephone or answering machine, see the Quick Guide for instructions.
a telephone wall jack to the LINE port on the NX300 Series. To connect a
telephone or answering machine, see the Quick Guide for instructions.
Note: If you’re connecting to a DSL phone line, you must use a DSL filter or
you won’t be able to fax. Contact your DSL provider for the necessary filter.
you won’t be able to fax. Contact your DSL provider for the necessary filter.
Connect the phone cord
6
Select your country:
1
Press
or
to select Country/Region,
then press OK.
2
Press
or
to select your Region,
then press OK.
3
If you change the region, confirm your
selection at next screen by pressing the
1 key (for yes) on the numeric keypad.
Enter the date and time:
1
Press
or
to select Daylight Saving Time, then press OK.
2
Press
or
to select Summer, if your
region uses Daylight Saving Time and
it’s currently in effect. (DST is effective
from spring to summer.) Otherwise select
Winter to turn off the setting.
3
Press OK.
4
Press
or
to select Date/Time, then press OK.
5
Press
or
to select the type of
date display, then press OK.
6
Use the numeric keypad to change
the date, then press OK.
7
Press
or
to select a 12-hour or 24-hour
display, then press OK.
8
Use the numeric keypad to set the time.
9
If you selected 12h, Press
or
to
select AM or PM.
10
Press OK.
When you’re finished choosing your settings, press Menu to exit.
Auto Answer/
Space
Redial/Pause
Stop/
Clear Settings
B&W
Color
Copy/Fax
Speed Dial
Group Dial/
Backspace
4