Sony UP-970AD User Manual
Digi
ta
l Mo
de
Printing
33
Printing
Before Starting a Print Job
Always check the following points:
• Unit connected correctly? (page 26)
• Paper loaded correctly? (page 9)
• Menu settings and menu adjustments done correctly?
Always check the following points:
• Unit connected correctly? (page 26)
• Paper loaded correctly? (page 9)
• Menu settings and menu adjustments done correctly?
Starting a Print Job
You can set up the printing direction, image size, all
sorts of settings for printing, using the menu. This
section describes operations after completing all sorts of
settings using the menu.
sorts of settings for printing, using the menu. This
section describes operations after completing all sorts of
settings using the menu.
1
Press the power ON/OFF switch to turn the unit on.
The back light on the LCD lights in green, and
“READY” is displayed on the LCD.
The back light on the LCD lights in green, and
“READY” is displayed on the LCD.
2
Print the image using the application software.
When the message is displayed on the LCD
If a problem occurs, the back light on the LCD lights in
umber and the error message stating the problem is
displayed on the LCD.
If a problem occurs, the back light on the LCD lights in
umber and the error message stating the problem is
displayed on the LCD.
When the unit stops printing during printing
When printing almost black images continuously, the
thermal head protection circuit may shut down the unit
to prevent the thermal head from overheating. In such a
case, the message “COOL” is displayed on the LCD.
Leave the unit until the head cools down and this
message disappears.
When printing almost black images continuously, the
thermal head protection circuit may shut down the unit
to prevent the thermal head from overheating. In such a
case, the message “COOL” is displayed on the LCD.
Leave the unit until the head cools down and this
message disappears.
To cancel a print job in progress
To cancel a print job in progress, press the OPEN/
CLOSE button, FEED button or CUT button.
To cancel a print job in progress, press the OPEN/
CLOSE button, FEED button or CUT button.
To feed paper
To feed paper, press the FEED button. The unit will
continue to feed paper as long as you hold down the
FEED button. Do not attempt to pull paper out of the
unit with your hand.
To feed paper, press the FEED button. The unit will
continue to feed paper as long as you hold down the
FEED button. Do not attempt to pull paper out of the
unit with your hand.
Paper currently selected
You can confirm the paper currently selected on the
LCD. The pointer points to the paper currently selected.
In the following figure, the currently selected paper is
the UPP-210SE paper.
You can confirm the paper currently selected on the
LCD. The pointer points to the paper currently selected.
In the following figure, the currently selected paper is
the UPP-210SE paper.
UP-990AD
Note
If “CT:ON” is selected in the “AT.CUT” menu,
quickly remove the prints that have been cut.
Otherwise, the cut prints may block the paper exit
and cause a paper jam to occur.
quickly remove the prints that have been cut.
Otherwise, the cut prints may block the paper exit
and cause a paper jam to occur.
UP-970AD
Making Copies of the Last Printout
Press the COPY button. The unit makes a copy of the
last printout. Each press of the COPY button prints the
number of images set in the “QTY” menu.
last printout. Each press of the COPY button prints the
number of images set in the “QTY” menu.
Note
If you press the COPY button immediately after turning
the power on, the alarm buzzer will sound as nothing is
stored in memory.
the power on, the alarm buzzer will sound as nothing is
stored in memory.
Message
Cause and remedy
EMPTY
Paper is not loaded. Load paper.
DOOR
The paper door is open. Close the
paper door.
paper door.
LCD
Indicates the UPP-210SE
Indicates the UPP-210HD
Indicates the UPT-210BL
Indicates the UPP-210SE
Indicates the UPP-210HD