Snapper SZT18336BVE User Manual
25
Section 4 - ADJUSTMENTS & REPAIR
WARNING
DO NOT attempt any adjustments, maintenance,
service or repairs with the engine running. Stop
engine. Stop blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and Vent
must be closed securely to prevent fuel spillage. DO
NOT attempt to service or charge the battery while it is
installed on the SCRAMBLER. Shield the positive
terminal with terminal cover located on battery
harness. This prevents metal from touching the
positive terminal, which could cause sparks. Cables
must be connected to battery terminals in the proper
position as shown.
service or repairs with the engine running. Stop
engine. Stop blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and Vent
must be closed securely to prevent fuel spillage. DO
NOT attempt to service or charge the battery while it is
installed on the SCRAMBLER. Shield the positive
terminal with terminal cover located on battery
harness. This prevents metal from touching the
positive terminal, which could cause sparks. Cables
must be connected to battery terminals in the proper
position as shown.
4.5 MOWER BLADE REPLACEMENT
4.5.3. BLADE REPLACEMENT
1. Remove blade(s). See Figure 4.17. Replace
blade(s) if it shows signs of excessive wear or
damage. See chart below for replacement
1. Remove blade(s). See Figure 4.17. Replace
blade(s) if it shows signs of excessive wear or
damage. See chart below for replacement
BLADE REPLACEMENT CHART
33” Blade
1-9523
38” Blades
2-4466 (Requires Two)
4.6 BATTERY
4.6.1. BATTERY REMOVAL
1. Tilt seat up to gain access to battery.
2. Observe and note cable positions on battery.
See Figure 4.18.
3.
1. Tilt seat up to gain access to battery.
2. Observe and note cable positions on battery.
See Figure 4.18.
3.
Disconnect cables from battery terminals,
disconnecting BLACK (Negative) cable first.
Disconnect RED (Positive) battery cable. Slide
battery from battery cradle.
4. Retain mounting bolts and nuts for future use.
Disconnect RED (Positive) battery cable. Slide
battery from battery cradle.
4. Retain mounting bolts and nuts for future use.
4.6.2. BATTERY INSTALLATION
1. Slide battery into battery cradle.
2. Connect cables to battery terminals. Connect
RED (Positive) cable first. Connect BLACK
(Negative) cable. See Figure 4.18.
3. Place the positive (+) terminal insulator over
positive terminal and cable. See Figure 4.18.
4.6.3. BATTERY SERVICE
1. Remove battery. Refer to Section “BATTERY
REMOVAL”.
2. Place battery in a well-ventilated area on a level
surface.
3. Using distilled water, refill cells as required to
cover cell plates of which can also be visualized
through the plastic battery case.
4. With cell caps removed, connect battery charger
to battery terminals. Red to positive (+) terminal
and black to negative (-) terminal.
1. Slide battery into battery cradle.
2. Connect cables to battery terminals. Connect
RED (Positive) cable first. Connect BLACK
(Negative) cable. See Figure 4.18.
3. Place the positive (+) terminal insulator over
positive terminal and cable. See Figure 4.18.
4.6.3. BATTERY SERVICE
1. Remove battery. Refer to Section “BATTERY
REMOVAL”.
2. Place battery in a well-ventilated area on a level
surface.
3. Using distilled water, refill cells as required to
cover cell plates of which can also be visualized
through the plastic battery case.
4. With cell caps removed, connect battery charger
to battery terminals. Red to positive (+) terminal
and black to negative (-) terminal.
5. Slow charge battery at 1 amp for 10 hours.
6. If battery will not accept charge or is partially
charged after 10 hours of charging at 1 amp,
replace with new battery, Part Number 6-0753.
6. If battery will not accept charge or is partially
charged after 10 hours of charging at 1 amp,
replace with new battery, Part Number 6-0753.
FIGURE 4.18
WARNING
The electrolyte (acid) produces a highly explosive gas.
Keep all sparks, flame and fire away from area when
charging battery or when handling electrolyte or
battery. Electrolyte (acid) is a highly corrosive liquid.
Wear eye protection. Wash affected areas immediately
after having eye or skin contact with electrolyte (acid).
Battery acid is corrosive. Rinse empty acid containers
with water and mutilate before discarding. If acid is
spilled on battery, bench, or clothing, etc., Flush with
clear water and neutralize with baking soda. DO NOT
attempt to charge battery while installed on the
SCRAMBLER. DO NOT use “BOOST” chargers on the
battery. If battery is removed, DO NOT operate engine
without insulating Positive + battery cable terminal with
electrical tape, or sparking from the battery cables can
result.
Keep all sparks, flame and fire away from area when
charging battery or when handling electrolyte or
battery. Electrolyte (acid) is a highly corrosive liquid.
Wear eye protection. Wash affected areas immediately
after having eye or skin contact with electrolyte (acid).
Battery acid is corrosive. Rinse empty acid containers
with water and mutilate before discarding. If acid is
spilled on battery, bench, or clothing, etc., Flush with
clear water and neutralize with baking soda. DO NOT
attempt to charge battery while installed on the
SCRAMBLER. DO NOT use “BOOST” chargers on the
battery. If battery is removed, DO NOT operate engine
without insulating Positive + battery cable terminal with
electrical tape, or sparking from the battery cables can
result.
4.6.4. BATTERY STORAGE
When SCRAMBLER is to be stored out of season,
it is recommended the battery be removed, charged
and stored.
1. Remove battery. (Refer to Section “BATTERY
REMOVAL”).
2. Perform battery service.
3. Bring battery to full charge, if required.
4.
When SCRAMBLER is to be stored out of season,
it is recommended the battery be removed, charged
and stored.
1. Remove battery. (Refer to Section “BATTERY
REMOVAL”).
2. Perform battery service.
3. Bring battery to full charge, if required.
4.
Store battery in an area away from the
SCRAMBLER on a wood surface. DO NOT STORE
BATTERY ON A CONCRETE SURFACE.
BATTERY ON A CONCRETE SURFACE.
BLACK
NEGATIVE (-)
CABLE
NEGATIVE (-)
CABLE
RED
POSITIVE (+)
CABLE
POSITIVE (+)
CABLE