Panasonic PT-LC56U User Manual

Before calling for service, check the following points.

B The power cord may not be connected.
B The MAIN POWER switch is turned off.
B The main power supply is not being supplied to the

wall outlet.

B TEMP indicator is illuminated or flashing. 
B LAMP indicator is illuminated or flashing. 
B The lamp unit cover has not been securely

installed.

B The video signal input source may not be

connected properly.

B The input selection setting may not be correct. 
B The BRIGHT adjustment setting may be at the

minimum possible setting.

B The shutter function may be in use.
B The lens cover may still be attached to the lens.
B The lens focus may not have been set correctly. 
B The projector may not be at the correct distance

from the screen.

B The lens may be dirty.
B The projector may be tilted too much. 
B COLOR or TINT adjustment may be incorrect. 
B The input source which is connected to the

projector may not be adjusted correctly.

B The audio signal source may not be connected

properly.

B The volume adjustment may be at the lowest

possible setting. 

B The battery may be weak.
B The battery may not be inserted correctly.
B The remote control signal receptor on the projector

may be obstructed.

B The remote control unit may be out of the

operation range.

B The CONTROL KEY may be set to “OFF”. 

In order to set the CONTROL KEY to “ON” without
using the remote control unit, keep holding down
the ENTER button on the projector and press the
MENU button for more than 2 seconds. It will then
be turned ON.

–
–
–

47
48

–

–

23
36

27

–

23
18

–

18
36

–

–

28,
31

–

21
21

21

44

+ Press the ENTER button to

display the OPTION2 screen,
and then use the F and G
buttons to select LAMP
RUNTIME.

, Press and hold the ENTER

The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.

- Turn off the power.

This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 24 for details on
how to turn off the power.

' Install the lamp unit cover, and

( Insert the power cord plug into

) Press the POWER button so

* Press the MENU button to

display the MAIN MENU
screen, and then press the F
and G buttons to move the
cursor to select “OPTION2”.

              M E N U

K E Y S T O N E

P I C T U R E

P O S I T I O N

I N D E X   W I N D O W

S H U T T E R

V O L U M E

L A N G U A G E

O P T I O N 1

O P T I O N 2

S E C U R I T Y

S E L E C T     E N T E R     E X I T

              O P T I O N 2

B A C K   C O L O R           B L U E

F R O N T / R E A R         F R O N T

D E S K / C E I L I N G       D E S K

F A N   C O N T R O L     S T A N D A R D

L A M P   P O W E R           H I G H

L A M P   R U N T I M E     1 8 2 0 H

F U N C   1                 I N D E X

C O N T R O L   K E Y           O N

A U T O   P O W . O F F   D I S A B L E

    S E L E C T                   R E T R N

              O P T I O N 2

B A C K   C O L O R           B L U E

F R O N T / R E A R         F R O N T

D E S K / C E I L I N G       D E S K

F A N   C O N T R O L     S T A N D A R D

L A M P   P O W E R           H I G H

T I M E   R E S E T   [ P O W E R   O F F ]

F U N C   1                 I N D E X

C O N T R O L   K E Y           O N

A U T O   P O W . O F F   D I S A B L E

    S E L E C T                   R E T R N

NOTE:
B Be sure to install the lamp unit

and the lamp unit cover securely.
If they are not securely installed,
it may cause the protection
circuit to operate so that the
power cannot be turned on.

NOTE:
BIf the POWER indicator on the

projector does not illuminate
red when the MAIN POWER
switch is turned on, turn the
MAIN POWER switch off again,
unplug the power cord from the
electrical outlet, and check that
the lamp unit and the lamp unit
cover are securely installed.
Then turn the MAIN POWER
switch back on.

NOTE:
B If the MENU button is pressed,

the lamp time resetting screen
will be cancelled.