Panasonic PT-EZ580 PT-EW640 PT-EX610 PT-EW540 PT-EX510 User Manual
Chapter 3 Basic Operations — Switching on/off the projector
48 - ENGLISH
6) If the input signal is an RGB signal, press the <AUTO SETUP> button.
7) Press the <ZOOM> button to adjust the size of the image to match the screen.
8) Press the <FOCUS> button again to adjust the focus.
9) Press the <ZOOM> button again to adjust the zoom and the size of the image to match the screen.
7) Press the <ZOOM> button to adjust the size of the image to match the screen.
8) Press the <FOCUS> button again to adjust the focus.
9) Press the <ZOOM> button again to adjust the zoom and the size of the image to match the screen.
Note
f
When the projector is switched on for the first time after purchase as well as when [ALL USER DATA] in the [PROJECTOR SETUP] menu →
[INITIALIZE] is executed, the focus adjustment screen is displayed after projection starts, then the initial setting screen is displayed. Refer to
“When the initial setting screen is displayed” (x page 45).
Switching off the projector
1)
2)
1)
4)
3)
2)
1) Press the power <v/b> button on the control panel or the power standby <v> button on the remote
control.
f
The
[POWER OFF(STANDBY)] confirmation screen is displayed.
2) Press qw to select [OK], and press the <ENTER> button.
(Or press the power <v/b> button on the control panel or the power standby <v> button on the
remote control again.)
f
Projection of the image will stop, and the power indicator <ON (G)/STANDBY (R)> on the projector body lights in orange. (The fan
keeps running.)
3) Wait for about 100 seconds until the power indicator <ON (G)/STANDBY (R)> on the projector body
lights in red.
4) Press the <OFF> side of the <MAIN POWER> switch to turn off the power.
Note
f
Do not switch on the projector and project images immediately after switching off the projector.
Turning on the power while the lamp is still hot may shorten the lamp life.
f
For about 75 seconds after the projector is switched off and the luminous lamp cooling is started, the lamp indicators will not light up even
if the power is switched on. Even after 75 seconds, the lamp may not light up if the projector is switched on. In such a case, after the power
indicator <ON (G)/STANDBY (R)> lights in red, switch on the projector again.
f
The projector consumes power even when the power <v/b> button on the control panel or the power standby <v> button on the
remote control is pressed and the projector is switched off if the main power of the projector is on.
When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], use of some functions is restricted,
but the power consumption during standby can be conserved.
Direct power off function
The projector can be turned off during projection or immediately after the luminous lamp is turned off by setting the <MAIN POWER> switch to
<OFF>. Also, when the projector is mounted on the ceiling or installed in an environment where the <MAIN POWER> switch of the projector
cannot be easily turned <OFF>, the power can be turned off directly using the circuit breaker. It is also safe in case a power outage occurs or
the power cord is pulled out immediately after the projector is switched off.
Note
f
If the projector was turned off by turning off the circuit breaker directly during projection last time, then the power indicator <ON (G)/
STANDBY (R)> will light in green a while after the circuit breaker is turned on, and then projection of the image will start.
f
If the power was turned off directly by turning the <MAIN POWER> switch to <OFF>, or the power was turned off by turning off the circuit
breaker directly, projection may take a longer time than usual to start when the projector is switched on the next time.