Panasonic PT-DW100 User Manual

Power supply

Power consumption

DLP

™ 

chip 

Panel size

 

Display method

 

Pixels

Lens
Lamp
Screen size

Brightness*

1

Contrast ratio*

1

Resolution
RGB input scanning frequency

Component signal

Video signal

Lens shift

Keystone correction range
Terminals 

DVI-D IN

 

RGB1/YP

B

P

R

 IN

 

RGB2 IN

 

VIDEO IN

 

VIDEO OUT

 

S-VIDEO IN

 

LAN

 

SERIAL IN

 

SERIAL OUT

 

REMOTE 1 IN

 

REMOTE 1 OUT

 

REMOTE 2 IN 

Optional board slot  With ET-MD77SD1
 

installed*

3

 

With ET-MD77SD3

 

installed*

3

 

With ET-MD100SD4

 

installed

 

With ET-MD77DV

 

installed

Installation
Power cord length
Dimensions (W x H x D)
Weight*

4

Operating temperature
Operating humidity
Supplied accessories

*

1

 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

*

2

 Only when using VESA CVT-RB(Reduced Blanking) signals.

*

3

 The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority.

*

4

 Average value. May differ depending on models.

*

5

 The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]).

Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be
reduced approximately 30% to protect the projector.

North America: 120–240 V AC, 16 – 9.0 A, 50/60 Hz (3-wire single-phase)
Europe, Asia: 220–240 V AC, 9.5 A, 50/60 Hz (3-wire single-phase)
North America: 1,600–1,500 W (10-15 W in standby mode with fan stopped)
Europe, Asia: 1,500 W (15 W in standby mode with fan stopped)
0.85" diagonal (16:9 aspect ratio)
DLP

™

 chip x 3 (R, G, B), DLP

™

 projection system

1,049,088 (1,366 x 768) x 3, total of 3,147,264 pixels
Optional powered zoom/focus lenses
300 W UHM lamp x 4 (four lamp system)
70 - 600 inches,16:9 aspect ratio 
(70-300 inches, 16:9 aspect ratio with the ET-D75LE5)
10,000 lumens (four-lamp operation mode)
5,000:1 (full on/full off, in Dynamic iris 3 mode)
1,366 x 768 pixels (Input signals that exceed this resolution will be converted to 1,366 x 768 pixels.)
fH 15-100 kHz, fV 24-120 Hz
Dot clock 20-162 MHz
480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
fH 15.75/15.63 kHz, fV 50/60Hz 
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Vertical: ±70% (±60% with the ET-D75LE6) (powered)
Horizontal: ±30% (±20% with the ET-D75LE6) (powered)
Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6)
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
720/60p, 720/50p
VGA (640 x 480) – WUXGA*

2

 (1,920 x 1,200), compatible with non-interlaced signals only,

Dot clock: 25–162 MHz
BNC x 5
D-sub HD 15-pin x 1
BNC x 1, 1.0 Vp-p
BNC x 1, 1.0 Vp-p
Mini DIN 4-pin x 1
RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
D-sub 9-pin male x 1 (RS422 x 1)
M3 jack x 1 for wired remote control
M3 jack x 1 for link control
D-sub 9-pin female x 1 for external control (parallel)
SERIAL IN: BNC x 1, SD-SDI signal (YC

B

C

R

 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

SERIAL OUT: BNC x 1, active through
SERIAL IN: BNC x 1, SD-SDI signal (YC

B

C

R

 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

Single-link HD-SDI signal (YC

B

C

R

 4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p,

1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
SERIAL OUT: BNC x 1, active through
Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YC

B

C

R

 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

Single-link HD-SDI signal (YC

B

C

R

 4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p, 1080/50i,

1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compliant: 1920 x 1080/50i,
1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF
Specifications are the same as those for the DVI-D IN terminal on the main unit.

Front/rear, ceiling/floor
3.0 m (9.8')
578 x 320 x 643 mm (22-3/4" x 12-19/32" x 25-5/16") (without lens)
Approx. 35 kg (77.2 lbs) without lens
0 -45 °C (32 -113 °F)*

5

10-80% (no condensation)
Power cord, Wireless/wired remote control unit,
Batteries for remote control (3V AA battery x2), Eye bolt x4, Wire rope

unit: mm (inch)

643 (25-5/16")

578 (22-3/4")

  

Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product

may be subject to export regulations. VGA and XGA are trademarks of International Business Machines Corporation.

All other trademarks are the property of their respective trademark owners.

Projection Images simulated.

DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments.

The PJLink trademark is an application trademark in Japan, the United States, and other

countries and regions or registered trademarks.

(C) 2008 Panasonic Corporation All rights reserved.

PT-DW100-08October50K Printed in Japan.

320 (12-19/32")

Throw distance

Diagonal image size

(aspect raio: 16:9)

ET-D75LE1 

1.5-2.0:1 

max.

min.

ET-D75LE2 

2.1-3.1:1

max.

min.

ET-D75LE3

3.1-5.2:1

max.

min.

ET-D75LE4

5.2-8.2:1

max.

min.

ET-D75LE8

8.2-15.4:1

max.

min.

ET-D75LE6

1.0-1.2:1

max.

min.

ET-D75LE5

0.8:1

fixed

3,103 mm

10.2'

4,476 mm

14.7'

6,765 mm

22.2'

9,053 mm

29.7'

13,630 mm

44.7'

18,206 mm

59.7'

27,360 mm

89.8'

2,322 mm

7.6'

3,349 mm

11.0'

5,062 mm

16.6'

6,775 mm

22.2'

10,201 mm

33.5'

13,626 mm

44.7'

20,477 mm

67.2'

4,719 mm

15.5'

6,787 mm

22.3'

10,234 mm

33.6'

13,680 mm

44.9'

20,574 mm

67.5'

27,467 mm

90.1'

41,254 mm

135.3'

3,137 mm

10.3'

4,516 mm

14.8'

6,814 mm

22.4'

9,112 mm

29.9'

13,707 mm

45.0'

18,303 mm

60.0'

27,494 mm

90.2'

7,937 mm

27.9'

11,391 mm

39.9'

17,147 mm

59.9'

22,904 mm

79.9'

34,416 mm

119.9'

45,929 mm

159.9'

68,954 mm

239.9'

4,730 mm

15.5'

6,798 mm

22.3'

10,244 mm

33.6'

13,691 mm

44.9'

20,584 mm

67.5'

27,477 mm

90.1'

41,264 mm

135.4'

12,713 mm

41.7'

18,206 mm

59.7'

27,359 mm

89.8'

36,512 mm

119.8'

54,819 mm

179.9'

73,126 mm

239.9'

109,740 mm

360.0'

7,943 mm

27.9'

11,397 mm

39.9'

17,153 mm

59.9'

22,909 mm

79.9'

34,422 mm

119.9'

45,934 mm

159.9'

68,960 mm

239.9'

23,652 mm

77.6'

33,943 mm

111.4'

51,095 mm

167.6'

68,246 mm

223.9'

102,549 mm

336.4'

136,852 mm

449.0'

205,458 mm

674.1'

12,430 mm

40.8'

17,923 mm

58.8'

27,077 mm

88.8'

36,232 mm

118.9'

54,541 mm

178.9'

72,850 mm

239.0'

109,468 mm

359.1'

1,865 mm

6.1'

2,696 mm

8.8'

4,081 mm

13.4'

5,466 mm

17.9'

8,236 mm

27.0'

11,006 mm

36.1'

16,546 mm

54.3'

1,151 mm

3.8'

1,681 mm

5.5'

2,563 mm

8.4'

3,445 mm

11.3'

5,209 mm

17.1'

—

—

1,560 mm

5.1'

2,253 mm

7.4'

3,408 mm

11.2'

4,563 mm

15.0'

6,873 mm

22.6'

9,183 mm

30.1'

13,803 mm

45.3'

PT-DW100

Highly Reliable Wide 10,000 lm Projector

1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, 

malfunction, or electric shock.

2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to 

illuminate, due to impact or extended use.

3. The projector uses high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

• Never place objects on top of the projector while it is in operation.

• Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust openings.

• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.

When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to 

installation where only one projector unit is operating at one time and the other unit is used as a backup.

• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure the 

projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.

4. If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp operation (lamp changer) 

function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three 

lamps for 8 hours of the 24 hours.

5. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage 

conditions.

• The brightness of the lamp will gradually decrease with use.

6. Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.
7. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.

70"

100"

150"

200"

300"

400"

600"

Zoom lens

ET-D75LE6 (1.0-1.2:1)

ET-D75LE1 (1.5-2.0:1)

ET-D75LE2 (2.1-3.1:1)

ET-D75LE3 (3.1-5.2:1)

ET-D75LE4 (5.2-8.2:1)

ET-D75LE8 (8.2-15.4:1)
Fixed focus lens

ET-D75LE5 (0.8:1)

ET-D75LE1

Replacement lamp unit

ET-LAD12KF (four pack)

SD-SDI input signal board

HD/SD-SDI input signal board

DVI-D input signal board

Dual link HD/HD-SDI input

signal board

High-ceiling

mount bracket

Low-ceiling

mount bracket

This optional

smoke filter must be used

for staging events where

smoke or fog is dispersed.

ET-PKD100H

ET-PKD100S

Panasonic works from every angle to minimize environmental impact in the 
product design, production and delivery processes, and in the performance of 
the product during its life cycle. The PT-DW100 reflects the following 
ecological considerations.
•Lead-free solder is used to mount components to the printed circuit boards.
•Lamp power switching further reduces power consumption.
•Auto Power Save activates standby mode when no signal is input.

PT-DW100 projector is 
carefully manufactured at 
the Panasonic factory in Japan 
under strict quality control. This is 
another very important advantage 
of Panasonic projectors.