Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. PT-DW8300E
  5. User Manual

Panasonic PT-DW8300E User Manual

Download
Page of 129
PROJECTOR SETUP menu
82
 - ENGLISH
Settings
Press ▲▼ to select [TIME] or 
4 ) 
[COMMAND] and change the setting 
according to the instructions of the 
menu.
TIME
Set the time at which the command 
will be executed using ▲▼ or numeral 
buttons.
COMMAND
Select a command to execute at the 
set time from the following.
POWER ON
• 
STANDBY
• 
SHUTTER 
• 
OPEN
SHUTTER 
• 
CLOSE
INPUT RGB1
• 
INPUT RGB2
• 
INPUT VIDEO
• 
INPUT S-VIDEO
• 
INPUT DVI-D
• 
INPUT HDMI
• 
INPUT SDI 
• 
Û
LAMP POWER 
• 
HIGH
LAMP POWER 
• 
LOW
LAMP DUAL
• 
LAMP SINGLE
• 
P IN P OFF
• 
P IN P USER1
• 
P IN P USER2
• 
P IN P USER3
• 
PT-DZ8700U/PT-DS8500U only
: 
Û
Press ▲▼ to select [STORE] and 
5 ) 
press <ENTER> button.
Note
If you try to register a setting that would cause the 
 
z
lamp to flash for a short time, an error message will be 
displayed on the screen. Set the [TIME] and [COMMAND] 
again.
To delete a command which has been set, press 
 
z
<DEFAULT> button.
If multiple commands have been set for the same time, 
 
z
they are executed in chronological order starting from the 
smallest command number.
The setting time operates under the local time.  
 
z
If an operation is executed with the remote control or 
 
z
control panel of the projector or with a control command 
before the command set in the schedule is executed, the 
command set with this function may not be executed.
RS-232C
This sets the communication parameters at the serial 
terminals.
Press ▲▼ to select [RS-232C].
1 ) 
Press <ENTER> button.
2 ) 
The [
 
z
RS-232C] screen will be displayed.
Press ▲▼ to select communication 
3 ) 
conditions.
press ◄► to change the setting.
4 ) 
Note
 
z
 
J
Selecting items in [EMULATE]
When using the control commands for one of our 
projectors that you have previously purchased to 
control this projector using a computer via its serial 
input terminal, set up the EMULATE function as 
follows. This will allow you to use the control software 
etc. designed for our existing projectors.
Select [EMULATE] in step 3).
1. 
Press <ENTER> button.
2. 
Press ▲▼ to select the required item.
3. 
Press <ENTER> button.
4. 
● DEFAULT
DZ8700 Series, DS8500 Series, 
DW8300 Series, D5000 Series, 
D6000 Series, DW6300 Series, 
DZ6700 Series, DZ6710 Series
D9610  
SERIES
D9510 Series, D9610 Series, 
D9500 Series, D9600 Series, 
D8500 Series, D8600 Series
D7700  
SERIES
D7500 Series, D7600 Series, 
D7700 Series, DW7000 Series
L6500  
SERIES
L6500 Series, L6510 Series, 
L6600 Series
 
J
About [EMULATE SETTING]
This sets which input signal can be selected using the 
input signal change command when a projector of a 
specific model is used with the emulate function.
Select [EMULATE SETTING] in step 3).
1. 
Press <ENTER> button.
2. 
The [EMULATE SETTING] screen will be 
 
z
displayed.
When the D9610 Series is selected 
 
Q
Press ▲▼ to select input signal 
1. 
[VIDEO], [S-VIDEO], [RGB1], [DVI-D] or 
[SDI].
[RGB2] and [HDMI] cannot be selected.
 
z
[SDI] is not shown for PT-DW8300U.
 
z
Press ◄► to select the input signal 
2. 
change command to be assigned to 
the selected input signal.
Selectable input signal change commands
 
z
When RGB1 is selected:
[INPUT1], [INPUT2], [INPUT3], [INPUT 
RGB], [NONE]
For all other instances:
[INPUT1], [INPUT2], [INPUT3], [NONE]
The same input signal change command 
 
z
cannot be assigned to multiple input signals.