Panasonic PT-AE3000E User Manual
B
asi
c Op
c Op
eration
Remote control operation
24 -
E
NGLISH
1. Select the required setting from MEMORY1 - 16.
Undefined setting will not be displayed.
2. Press the ENTER button to activate the selected
setting.
The aspect ratio will be selected automatically,
or you can switch it manually by pressing the
ASPECT button. Press the button several
times to cycle through the different aspect type.
See “ASPECT” on page 37.
or you can switch it manually by pressing the
ASPECT button. Press the button several
times to cycle through the different aspect type.
See “ASPECT” on page 37.
You can display the image brightness and
contrast level of the input signal with a
waveform. See “WAVEFORM MONITOR” on
page 33.
contrast level of the input signal with a
waveform. See “WAVEFORM MONITOR” on
page 33.
J
Displaying the waveform
1. Press the WAVEFORM button and display the
waveform monitor.
Press the WAVEFORM button again to escape from
the waveform mode.
the waveform mode.
2. Press ENTER button until the required waveform
option is displayed.
In FULL SCAN mode, press F G I H to change
the waveform position.
the waveform position.
In SINGLE LINE SCAN mode, press F G to select
the required line position.
the required line position.
Loading a saved setting
NOTE:
• If you have not saved any settings, MEMORY1 - 16 will
not be displayed.
Switching the aspect ratio
NOTE:
• If you project an image with an unmatched aspect ratio,
the image may distort or some portions may be
cropped. Select an aspect ratio which preserves the
intention of the image creator.
cropped. Select an aspect ratio which preserves the
intention of the image creator.
• The order of aspect type is defined not only by the input
method but also by the input signals. See “List of
compatible signals” on page 50.
compatible signals” on page 50.
• If you project a copyrighted image enlarged or distorted
by using ASPECT function in commercial use in a
public place, such as a restaurant or hotel, you might
infringe on the copyright of the creator which is
protected by copyright law.
public place, such as a restaurant or hotel, you might
infringe on the copyright of the creator which is
protected by copyright law.
Adjusting the signal condition with a waveform
FULL SCAN
Monitoring the waveform of
brightness and contrast of the whole
image.
brightness and contrast of the whole
image.
SINGLE LINE SCAN
Monitoring the waveform of
brightness and contrast in each
horizontal line of the image.
brightness and contrast in each
horizontal line of the image.
FULL SCAN(Y)
SINGLE LINE SCAN(B)
FULL SCAN(R)
SINGLE LINE SCAN(G)
FULL SCAN(G)
SINGLE LINE SCAN(R)
FULL SCAN(B)
SINGLE LINE SCAN(Y)
NOTE:
• In SINGLE LINE SCAN mode, the position of the waveform monitor depends on the position of the selected line.
• You can display the main menu by pressing the MENU button and adjust the menu items.
• The called up menu items displayed position depends on the position of the waveform monitor.
• You can activate AUTO ADJUST of the WAVEFORM menu by pressing the DEFAULT button.
• The signal which is lower than 0% in the waveform will be displayed as same as 0% on the projected image.
• While the waveform is displayed, the image is displayed without the COLOUR MANAGEMENT adjustment.
• When adjusting the KEYSTONE of the POSITION menu while the waveform is displayed, x.v.Colour will be deactivated.
• You can display the main menu by pressing the MENU button and adjust the menu items.
• The called up menu items displayed position depends on the position of the waveform monitor.
• You can activate AUTO ADJUST of the WAVEFORM menu by pressing the DEFAULT button.
• The signal which is lower than 0% in the waveform will be displayed as same as 0% on the projected image.
• While the waveform is displayed, the image is displayed without the COLOUR MANAGEMENT adjustment.
• When adjusting the KEYSTONE of the POSITION menu while the waveform is displayed, x.v.Colour will be deactivated.