Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. PT-RW330U
  5. User Manual

Panasonic PT-RW330U User Manual

Download
Page of 128
Chapter 3  Basic Operations — Switching on/off the projector
ENGLISH - 33
Indicator status
Status
Off
The main power is switched off.
Red
Flashing
The power is switched off (in standby mode). [STANDBY MODE] is set to [NORMAL].
Projection will start when the power <v/b> button is pressed.
 
f
The projector may not operate when the temperature indicator <TEMP> is flashing. 
(x page 109)
Lit
The power is switched off (in standby mode). [STANDBY MODE] is set to [ECO].
Projection will start when the power <v/b> button is pressed.
 
f
The projector may not operate when the temperature indicator <TEMP> is flashing. 
(x page 109)
Green
Lit
Projecting.
Note
 
f
The projector consumes power even in standby mode (the power indicator <ON (G)/STANDBY (R)> lights/flashes in red).
Refer to “Power consumption” (x page 123) for the power consumption.
 
f
The power indicator <ON (G)/STANDBY (R)> flashes in green if a remote control signal is received.
 
f
The power indicator <ON (G)/STANDBY (R)> flashes in green slowly when the projector is in AV mute mode.
Switching on the projector
1)
3)
2)
3)
1) 
Connect the power plug to an outlet.
 
f
(AC 100 V - 240 V 50 Hz/60 Hz)
2) 
Press the <ON> side of the <MAIN POWER> switch to turn on the power.
 
f
The power indicator <ON (G)/STANDBY (R)> lights/flashes in red, and the projector enters the standby mode.
3) 
Press the power <v/b> button.
 
f
The power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Note
 
f
If the projector is switched on at around 0 °C (32 °F), a warm-up period of approximately five minutes may be necessary until an image is 
displayed.
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP> 
turns off and the projection starts. Refer to “Managing the indicated problems” (x page 109) for the indicator status.
 
f
If the operating environment temperature is low and warm-up takes more than five minutes, the projector will judge that a problem has 
occurred and the power will automatically be set to standby mode. If this happens, increase the operating environment temperature to 0 °C 
(32 °F) or higher, turn off the main power, and then turn on the power again.
 
f
If the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] (x page 71) is set to [ECO], there may be a delay in 
displaying when the power is turned on compared to when the setting is [NORMAL].
 
f
When the power is turned or an input signal is switched, you may here a high-frequency driving sound. This is not a malfunction.
 
f
If the [PROJECTOR SETUP] menu → [INITIAL STARTUP] (x page 74) is set to [LAST MEMORY] and the power is turned off by pressing 
the <OFF> side of the <MAIN POWER> switch or by using the breaker directly while projecting at the last time of use, the power indicator 
<ON (G)/STANDBY (R)> lights in green and projection starts after a while when the power is turned on by pressing the <ON> side of the 
<MAIN POWER> switch with the power plug connected to the outlet, or when the breaker is turned on.