IBM 12.1(22)EA6 User Manual
20-6
Cisco Systems Intelligent Gigabit Ethernet Switch Modules for the IBM BladeCenter, Software Configuration Guide
24R9746
Chapter 20 Configuring System Message Logging
Configuring System Message Logging
Synchronizing Log Messages
You can configure the system to synchronize unsolicited messages and debug privileged EXEC
command output with solicited device output and prompts for a specific service port line or virtual
terminal line. You can identify the types of messages to be output asynchronously based on the level of
severity. You can also determine the maximum number of buffers for storing asynchronous messages
for the terminal after which messages are dropped.
command output with solicited device output and prompts for a specific service port line or virtual
terminal line. You can identify the types of messages to be output asynchronously based on the level of
severity. You can also determine the maximum number of buffers for storing asynchronous messages
for the terminal after which messages are dropped.
When synchronous logging of unsolicited messages and debug command output is enabled, unsolicited
device output appears on the console or is printed after solicited device output appears or is printed.
Unsolicited messages and debug command output appears on the console after the prompt for user input
is returned. Therefore, unsolicited messages and debug command output are not interspersed with
solicited device output and prompts. After the unsolicited messages appear, the console again displays
the user prompt.
device output appears on the console or is printed after solicited device output appears or is printed.
Unsolicited messages and debug command output appears on the console after the prompt for user input
is returned. Therefore, unsolicited messages and debug command output are not interspersed with
solicited device output and prompts. After the unsolicited messages appear, the console again displays
the user prompt.
Beginning in privileged EXEC mode, follow these steps to configure synchronous logging:
Command
Purpose
Step 1
configure terminal
Enter global configuration mode.
Step 2
line [console | vty] line-number
[ending-line-number]
[ending-line-number]
Specify the line to be configured for synchronous logging of
messages.
messages.
•
Use the console keyword for configurations that occur through
the switch service port.
the switch service port.
•
Use the line vty line-number command to specify which vty
lines are to have synchronous logging enabled. You use a vty
connection for configurations that occur through a Telnet
session. The range of line numbers is from 0 to 15.
lines are to have synchronous logging enabled. You use a vty
connection for configurations that occur through a Telnet
session. The range of line numbers is from 0 to 15.
You can change the setting of all 16 vty lines at once by entering:
line vty 0 15
Or you can change the setting of the single vty line being used for
your current connection. For example, to change the setting for vty
line 2, enter:
your current connection. For example, to change the setting for vty
line 2, enter:
line vty 2
When you enter this command, the mode changes to line
configuration.
configuration.
Step 3
logging synchronous [level severity-level |
all] [limit number-of-buffers]
all] [limit number-of-buffers]
Enable synchronous logging of messages.
•
(Optional) For level severity-level, specify the message severity
level. Messages with a severity level equal to or higher than this
value are printed asynchronously. Low numbers mean greater
severity and high numbers mean lesser severity. The default is 2.
level. Messages with a severity level equal to or higher than this
value are printed asynchronously. Low numbers mean greater
severity and high numbers mean lesser severity. The default is 2.
•
(Optional) Specifying level all means that all messages are
printed asynchronously regardless of the severity level.
printed asynchronously regardless of the severity level.
•
(Optional) For limit number-of-buffers, specify the number of
buffers to be queued for the terminal after which new messages
are dropped. The default is 20.
buffers to be queued for the terminal after which new messages
are dropped. The default is 20.
Step 4
end
Return to privileged EXEC mode.